Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
If outside air is installed, the inlet cover may be blocked. 3. The air chamber under the burnpot may be filled with fines and small bits of ash. 4. The holes in the burnpot may be getting filled with ash or carbon buildup. 5. Combustion blower fan blades may need cleaned. 6. There is no fuel in the hopper. SMOKE SMELL Seal the vent pipe joints and connection to stove with silicone. FIRE HAS GONE OUT 1. No pellets in hopper. 2. Draft setting is too low. 3. Something is restricting fuel flow. 4. Feed motor or combustion blower has failed. 5. Power failure or blown fuse. SMOKE IS VISIBLE COMING OUT OF VENT 1. Air-fuel ratio is too rich. A. Feed rate too high. B. Draft too low caused by a gasket leak. LOW HEAT OUTPUT 1. Feed rate too low 2. Draft too low because of gasket leak. 3. Poor quality or damp pellets 4. Combination of 1 and 2. Helpful Hints Cleaning Burn Pot Whenever your stove is not burning, take the opportunity to scrape the burn pot to remove carbon buildup. A vacuum cleaner is handy to remove the residue. Be sure the stove is cold if you use a vacuum. Carbon buildup can be scraped loose with the fire burning using the special tool provided with your stove. Scrape the floor and sides of the burn pot. The carbon will be pushed out by the incoming fuel. Always wear gloves to do this. Removing Ashes Turn the Temp Dial to number 1 approximately 30 minutes before removing ashes. This will result in a cooler stove and ash pan. Maximum Feed Adjuster settings are not needed in most cases. Operating in the normal range (#4) is recommended when maximum heat output is not required. The ESP probe prevents the stove from being over-fired. Keep the stove free of dust and dirt. Fuel Pellet fuels are put into 3 categories in terms of ash content. Premium at 1% or less, Standard at 3% or less and all others at 3% or more. The P68 is capable of burning all 3 categories of pellets due to a patented feeder and burn pot system. Itshould be noted, however, that higher ash content will require more frequent ash removal, scraping of the burn pot, and may provide less BTU's per pound. Normally, standard and high ash pellets cost less than premium pellets and can be cost effective when burned in the P68. The moisture content must not exceed 8%. Higher moisture will rob BTU's and may not burn properly. P68 Pellet Stove 27 28 P68 Pellet Stove Weight 290 lbs. Blower 135 cfm Feed Rate approx. 1lb. to 8 lbs per hr Hopper Capacity 76 lbs Fuel Wood Pellets Flue Size 3 inch Outside Air Size 2 3/8" I.D. inch Fuse Rating 6 amp P61A Feeder Specifications P68 Feeder and Specifications 3- 30- 1371612513 MOTOR BLADE 3- 20- 2046399 ( 4) 3- 30- 2252005013 P68 Pellet Stove 29 OPTIONS Side Heat Shields Side heat shields are available to reduce the clearance to combustible materials. Part #1-00-06716 Hopper Extension The hopper extension allows you to put more pellet fuel in the hopper and extends burn time on one load of pellets. The hopper extension adds 60 pounds to the existing 76 pound hopper capacity, allowing you to load 136 pounds of pellets at one time. Part #1-00-08636 Floor Protector The P68 Steel Floor Protector measures 25 inches wide by 33 inches deep. It is made of 20 gauge steel. This is the minimum size for floor protection with this unit. Part# 1-00-06727 20 gauge steel floor protector Decorative Tile/Grey Slate Options The decorative tile and slate measure 11.938" x 5.938". The tile/slate trim is necessary to hold the tile/slate in place on the stove. There are 10 decorative tile choices, and 4 decorative slate choices. See dealer for samples. 33" 25" 5.938" 11.938" frame tile/slate 30 P68 Pellet Stove P68 Wiring Diagram J2 68 6 P68 Parts List P68 Parts List Description Part Number Hopper Gasket(6 ft.) 0-88-00248 Ash Pan Assembly 1-10-05800 Burn Pot Weldment 1-10-06723 Right Rear Shield 2-00-06468-1 Left Rear Shield 2-00-06468-2 Arrow Scraper 2-00-773850 Flame Guide 3-00-674069 Wiring Harness Assembly 3-20-08727 Thermister Probe 3-20-00744 Room Sensor 3-20-00906 Circuit Board 3-20-05374 Differential Switch 3-20-9301 5" Double Fan Blade 3-20-502221 Combustion Blower 3-21-08639 Distribution Blower 3-21-22647 Hopper Lid Latch 3-31-199110 3/16" Rubber Washer (for Hopper Lid) 3-31-90131101 Power Cord 3-20-29685 Auto Ignite Label (Control Panel Door) 3-90-08627 Fire Brick (3) 3-40-900450125 White/Black Control Knob(3) 3-31-605 Control Knob Shaft(3) 3-31-015 Mirrored Front Glass 3-40-06720 Burn Pot Gasket(1) 3-44-00409 Tailpipe Gasket 3-44-06179 Wiring Diagram 3-89-06504 Control Panel Sticker 3-90-06655A Owner's Manual 3-90-06701 Hopper Lid Label 3-90-08416 Ignitor Assembly 1-10-06620 Cleanout Cover(1) 2-00-06623 1/4-20 x 1/2" Wing Screw w/Collar(2) 3-31-782108 Hopper Extension Assembly Options: 1-00-08636 Outside Air Assembly 1-10-08542 3' Flex Pipe 2-00-08543 Log Set 3-40-5647 Side Heat Shields 1-00-06716 Floor Protector (25" x 33") 1-00-06727 Air Grill 3-43-08648 (See Dealer for finish options) Door Frame w/ash lip & tile/slat...