Évaluations - 2, GPA: 4.5 ( )

Fabricant : DCS Taille : 3.37 mb Nom Fichier : Langue d'enseignement:

OVEN DOOR REMOVAL WARNING! Do not lift oven door by the handle - will cause damage! Be sure the oven and door are cool before you begin to remove the door! 1. Open the door all the way open (Fig 22). 2. Unlock the door hinges by rotating the lock forward (Fig.23). 3. Once both hinges are unlocked, gently close the door until approximately halfway closed. Grabbing the sides of the door and gently lifting up and slightly forward, the door will unlatch from the hinge. 4. Continue to lift and pull the door away from the range. Fig. 22 1. 2. 3. 4. 5. Close the oven door. OVEN DOOR INSTALLATION Position the door in approximately halfway open position. Simply place the hinge tongue into the hinge slots (See Fig. 24). Push the door into the slots until you feel them fall into the latches. Open the door completely and rotate the locks into the closed position (Fig. 25). Oven hinge assembly Hinge retainer clip in unlocked position Fig. 25Hinge retainer clip in locked position hinge slot hinge tongue Fig. 24Hinge assembly CARE AND MAINTENANCE OVEN RACKS AND RACK SUPPORTS All of the oven racks and 12” rack supports are chrome plated steel. The roller assisted rack supports in the main oven (24” and 27”) are stainless steel. To remove the 12” Oven rack supports, first remove the oven racks, then grasp the rack supports and pull up and out. To replace the rack supports, put the top in first. To clean, use a damp sponge, cloth, or steel wool with a mild detergent. Chrome cleaners, such as Soft Scrub, Cameo or Bar Keepers Friend can be applied with a damp sponge following package directions. Rinse and dry. Powdered cleaners such as Bon-Ami or Comet are applied with a damp sponge or cloth, rubbed lightly, rinsed and dried. For hard to remove food soil use a dampened soap filled steel wool pad, rinsed and dried. Harsh cleaners which are commercial oven cleaners, such as Easy Off or Dow can be used on the racks, but are not recommended for use on the self cleaning oven rack rollers or oven interiors. Additionally, some commercial oven cleaners cause darkening and discoloration. Test the cleaner on a small part of the rack and check for any discoloration before cleaning the entire rack. Apply a generous coating. Allow to stand for 15 to 20 minutes. Rinse thoroughly and dry. After being cleaned, if the racks in the main oven do not slide easily, pour a small amount of cooking oil on a paper towel and rub it lightly over the side rails and rollers. Spray rollers with “Pam” if racks get hard to move. FRAME, SIDES, DOOR EXTERIOR, HEAT DEFLECTOR These parts are made of stainless steel, follow the directions for the Backguard. Take care when cleaning the door top, and do not let water or cleaners run down the vents. If water or cleaners spill into the vents, they may streak the glass inside the door. DOOR GASKET Clean with hot water only. Do not rub. Press a dry towel on the gasket to dry. Do not remove or damage the mesh. OVEN LIGHT BULB REPLACEMENT For oven light bulb replacement use only a 40 watt, 120 volt appliance light bulb. These are available in supermarkets. DO NOT use a standard light bulb in any oven, the heat will break it. To Replace the Light Bulb 1. Be sure the oven light bulb switch is in the “OFF” position or turn off circuit breaker. The bottom of the switch is pressed in. Let the cover and the bulb cool completely. 2. Remove the light cover. Turn the cover to the left (counterclockwise) to unscrew it. 3. Remove the burnt out bulb. Replace it with a 40 watt appliance light bulb only. 4. Replace cover. Turn circuit breaker back on, if turned off. (See Warning below). WARNING! Be sure the oven light switch is in the OFF position and the cover is cool. If the bulb comes loose from the base, turn off the power to the oven at the circuit breaker panel, before attempting to remove the bulb base from the socket. POWER FAILURE To light the cooktop burners, turn the control knob to “LITE”, hold a lighted match to the port ring. After the flame is burning all the way around the burner, adjust the flame. It is necessary to light each burner separately, each time you want to use it. Do not attempt to match light the griddle, grill, broil burners, or oven; they will not function without any electrical power. Make sure knobs are in the “OFF” position should power be restored and you are away from the unit. Do not leave the burner unattended. The burner will not relight if blown out. TROUBLESHOOTING RANGES & COOKTOPS PROBLEM POSSIBLE CAUSE SOLUTION NON FUNCTIONAL NO ELECTRICITY OR GAS SUPPLY TURN ON GAS SUPPLY VALVE CHECK CIRCUIT BREAKERS TECHNICAL CALL AUTHORIZED SERVICE ONE OR MORE BURNERS WILL NOT LIGHT NO ELECTRICITY CHECK CIRCUIT BREAKERS NO GAS CHECK GAS SUPPLY AT WALL WRONG GAS VERIFY GAS TYPE (SEE PAGE 33 FOR LOCATION OF LABEL DIRTY BURNERS CLEAN BURNERS BURNERS MIS-ALIGNED ALIGN & REASSEMBLE BURNERS WATER IN BURNER(S) DIS-ASSEMBLE & DRY BURNER(S) DIRTY ELECTRODE CLEAN BURNER ELECTRODE TECHNICAL CALL AUTHORIZED SERVICE I...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :