Évaluations - 4, GPA: 4.3
(
)
)
|
Facilité d'utilisation
Figure 32.1. d. Remove 2 screws to remove the thermostat block and disconnect the 2 yellow wires. e. Remove the 2 screws from the power inlet and rotate it through the hole and out of the screen, leaving the wires attached. f. Disconnect the vacuum hose and both wires (orange and red) from the vacuum switch attached to the rear screen. g. Remove both wires from exhaust blower (blue and double white). h. Remove 6 screws using a flathead screwdriver or a 1/4" nutdriver. Retain screws for use on replacement blower. Figure 32.2. i. Remove exhaust blower and gasket. j. Install new gasket and blower. Discard blower housing if not needed. k. Re-install in reverse order. Figure 32.1 Combustion Blower Remove 7 screws and bend top back leaving it attached at the bottom. Remove 6 screws Figure 31.2 Figure 32.3 Castile Pellet Stove R E. Igniter Replacement hm S re gniter gniterra ket Figure 33.1 a. Turn down thermostat, let the appliance completely cool and then unplug appliance before servicing. b. Open the ash door and remove the ash pan. Remove the left side panel by loosening 2 screws (do not remove) and pull side panel away. c. The wire leads to the igniter are connected to the wire harness (black wires) with 1/4 inch male / female spade connectors. Disconnect the spade connections. Loosen the thumb screw and slide igniter out. c. Install new igniter into the chamber and tighten the thumb screw. d. Re-connect the wires to the 2 leads with the spade connectors. Double check that the igniter wires are clear of any movement, i.e. ash pan, firepot cleaning rod, cleaning slide plates, etc. f. Re-install the ash pan, close the ash removal door. F. Baffle Removal Figure 33.2 Push Up Latch Slide Top Baffle Forward and Down Face of Stove Latch Top Baffle Figure 33.3 Hook on Second Notch Latch NOTE: There is a latch on the appliance to keep the top baffle from coming out during shipment or when the heat exchanger scraper rods are pulled. a. Allow appliance to cool completely. b. Open doors and locate the latch. It is located between the front edge of the top baffle and the inside of the firebox centered from side to side. The latch pivots up and down. c. Push the latch up with your finger while sliding the top baffle forward and down. Figure 33.2. d. To re-install the top baffle, align the hooks on the baffle with the slots in the baffle hangers, push up and slide back. Figure 33.3. e. Make sure the latch drops back into position, bypassing the first notch and catching the front edge of the top baffle with the second small notch. September 1, 2008 250-6422E Page 33 R R Castile Pellet Stove G. Glass Replacement WARNING • • • Glass is 5mm thick high temperature heat- resistant ceramic glass. DO NOT REPLACE with any other material. Alternate material may shatter and cause injury a. Open the face and remove door from the appliance by lifting door off of hinge pin and lay on a flat surface face down. b. Using a screwdriver, tap the bottom of the rope retainer rod to push it up out of the hole. The top end of the rod will slide up. Swing the rod toward you from the bottom and remove the rod. Repeat for other side. c. Remove old glass and replace with new glass. d. Slide the retainer rod into the top hole first, and then line up the bottom crimped end with the hole in the door. The crimped end must be parallel with the glass in order to insert it into place. Figure 34.1. Glass Rope Retainer Rods Crimped end at the bottom Crimped end must be parallel with the glass Slide top end in first Figure 34.1 Page 34 250-6422E September 1, 2008 Castile Pellet Stove 11 Reference Materials R A. Component Function 1. Control Box • When describing the location of a component, it is always AS YOU FACE THE FRONT OF THE APPLIANCE. a. The control box is located on upper right side of appliance, behind the right side panel and above the vacuum switch. b. There is a light located inside of the control box. The internal light will turn green when the appliance has reached a temperature of 175.F (79°C) in the firepot. and will turn red when it reaches 600oF (315°C). c. There is also an internal blue light located in the upper left corner of the control box. When you plug in the appliance the blue light will automatically start blinking 4 times in a row for 60 seconds and then will stop. NOTE: Do NOT open the control box. This will void the warranty. FolIow proper shutdown procedures first if you need to plug in or remove the control box. 2. Convection Blower The convection blower is mounted at the bottom rear of the appliance. There are 2 impellers, one on each side of the motor. The convection blower pushes heated air through the heat exchange system into the room. 3. Combustion Blower The combustion blower is located on the right side of appliance and is designed to pull the exhaust from the appliance and push it out through the venting system. 4. Feed System The feed system is located on the right side of the appliance and can be removed as an entire...
Ce manuel est également adapté pour les modèles :Plate - CASTILE-CSB (2.86 mb)
Plate - CASTILE-CWL (2.86 mb)
Plate - CASTILE-MBK1 (2.86 mb)