Évaluations - 2, GPA: 4.5
(
)
)
|
Facilité d'utilisation
Use a backup wrench on the elbow fitting to avoid damage. 2. Install male 1/2" or 3/4" flare union adapter on the NPT internal thread of the manual shut-off valve. 3. Connect flexible metal appliance connector. 4. Make sure circuit breaker is off and then plug range cord in to electrical outlet. 5. Push range back into position insuring that range leg slides under the anti-tip bracket. The range will sit 3/4" away from the wall when properly installed. Note: Be careful not to crimp flexible connector! 6. Carefully tip range forward to insure that anti-tip bracket engages and prevents tip-over. Rigid Pipe Method (see Figure 12, this page) The configuration of the rigid pipe connection will vary depending on the location of the gas pipe stub. Refer to Figure 12 for details. 1. Make sure circuit breaker is off and then plug range cord in to electrical outlet. 2. Push range back into position insuring that range leg slides under the anti-tip bracket. The range will sit 3/4" away from the wall when properly installed. 3. Carefully tip range forward to insure that anti-tip bracket engages and prevents tip-over. 4. Connect pipe to range at union. Access the connection through the access panel behind the warming drawer. Note: Be careful not to apply pressure to warming drawer element during rigid pipe installation. Proceed to "Test for Gas Leaks", next column. Test for Gas Leaks. Leak testing is to be conducted by the installer according to the instructions given in this section. Turn on Gas. Apply a non-corrosive leak detection fluid to all joints and fittings in the gas connection between the shut-off valve and the range. Include gas fittings and joints in the range if connections were disturbed during installation. Bubbles appearing around fittings and connections indicate a leak. If a leak appears, turn off supply line gas shut-off valve and tighten connections. Retest for leaks by turning on the supply line gas shut-off valve. When leak check is complete (no bubbles appear), test is complete. Wipe off all detection fluid residue. Proceed to Step 6: Test the Installation CAUTION ^ NEVER CHECK FOR LEAKS WITH A FLAME. DO NOT CONTINUE TO THE NEXT STEP UNTIL ALL LEAKS , ARE ELIMINATED. > CAUTION: Before you plug in an electrical cord, be sure all controls are in the OFF position. 6 Step 6: Test the Installation 1. Test Electric Ignition. Turn on power at breaker. If LCD screen flashes and beeps continuously, the wiring is incorrectly installed. Immediately disconnect power at breaker and return to step 4: CONNECT RANGE CORD. Select a rangetop burner knob. Push down and turn to the flame symbol. If the ignitor/spark module is operating correctly, it will produce a clicking sound. Once the air has been purged from the supply lines, the burner should light within four (4) seconds. After burner lights, turn knob to the off position. Test each rangetop burner in this fashion. Call Bosch Service (800-944-2904) if any of the burners do not light. Some yellow streaking is normal during the initial start-up. Allow unit to operate 4-5 minutes and reevaluate before making adjustments. 2. Test/Adjust Flame. High Setting: The combustion quality of the flame for each burner must be visually inspected. For propane, the flame should be blue with yellow tips. For natural gas, it should be soft blue in color. The flame should carry over, or surround, the entire burner and should not lift or blow off the burner. To inspect, turn the burner on. See Figure 14 for appropriate flame characteristics. If the flame is completely or mostly yellow, verify that the regulator is set for the correct fuel. After adjustment, retest. If any of the burners continue to burn mostly or completely yellow, call Bosch Service (800-944-2904). Note: With LP use, some yellow tipping on outer cones is normal. Low Setting All burners must also be inspected for carryover. On low, the flame should completely surround the burner. If any of the cooktop burners do not carry over on the low setting, call Bosch Service (800-944-2904). Figure 14 Flame Characteristics Yellow Flames: Further adjustment is required. Yellow Tips on Outer Cones: Normal for LP Gas. Soft Blue Flames: Normal for Natural Gas. mm mm Installation is complete at this time. WHEN PROPERLY ADJUSTED: There should be a flame at each burner port. There should be no air gap between the flame and burner Replacement Parts: Visit your Bosch dealer for replacement parts. For a dealer near you contact Bosch service: 800-9442904 or Page 7 A INSTRUCTIONS DE SÉCURITÉ IMPORTANTES Lire toutes les instructions avant de procéder /-N Table des matières Instructions de sécurité et codes applicables......................................................................1, 2 Installation ventilation, préparation des armoires et installation des fixations anti basculement.... 3 Connexion électrique........................................
Ce manuel est également adapté pour les modèles :Plate - HDS252U (3.3 mb)
Plate - HDS255U (3.3 mb)