Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
Если вам надо обратиться в сервисный центр: Внимание! При ремонте требуйте использования оригинальных запасных частей. Другую полезную информацию и новости Вы можете найти на сайте в разделе «Сервис». 12 Installation ! Before operating your new appliance please read this instruction booklet carefully. It contains important information concerning the safe installation and operation of the appliance. ! Please keep these operating instructions for future reference. Make sure that the instructions are kept with the appliance if it is sold, given away or moved. ! The appliance must be installed by a qualified professional according to the instructions provided. ! Any necessary adjustment or maintenance must be performed after the appliance has been disconnected from the electricity supply. Positioning and levelling ! It is possible to install the appliance alongside cupboards whose height does not exceed that of the hob surface. ! Make sure that the wall in contact with the back of the appliance is made from a non-flammable, heat- resistant material (T 90°C). To install the appliance correctly: • Place it in the kitchen, dining room or the bed-sit (not in the bathroom). • If the top of the hob is higher than the cupboards, the appliance must be installed at least 200 mm away from them. HOOD 420Min.min. 650 mm. with hoodmin. 700 mm. without hoodmm. 600Min. mm. 420Min. mm. • If the cooker is installed underneath a wall cabinet, there must be a minimum distance of 420 mm between this cabinet and the top of the hob. This distance should be increased to 700 mm if the wall cabinets are flammable (see fi gure). • Do not position blinds behind the cooker or less than 200 mm away from its sides. • Any hoods must be installed according to the instructions listed in the relevant operating manual. Levelling If it is necessary to level the appliance, screw the adjustable feet* into the places provided on each corner of the base of the cooker (see fi gure). The legs* provided with the appliance fit into the slots on the underside of the base of the cooker. Electrical connection Fitting the power supply cable The cable should be suited to the type of electrical connection used, according to the following connection 400V 3N~ H05RR-F 5x2.5 CEI-UNEL 35363 H05VV-F 5x2.5 CEI-UNEL 35746 1 2 3 4 5 S T N R 400V 2N~ H05RR-F 4x4 CEI-UNEL 35363 H05VV-F 4x4 CEI-UNEL 35746 230V 1N~ H05RR-F 3x4 CEI-UNEL 35363 H05VV-F 3x4 CEI-UNEL 35746 R 123451234 5 R SNN V diagram: To install the power supply cable correctly: 1. Loosen the screw V in the terminal board and pull the cover to open it (see fi gure). 1 2 3 N A B 2. Position the connection support A (see fi gure) according to the connection diagram shown above. The terminal board is designed for single-phase 230 V connection: terminals 1, 2 and 3 are connected to each other; jumper 4-5 is located in the lower area of the terminal board. 3. Position wires N and .according to the diagram (see fi gure) and perform the connection by tightening the terminal board screws as much as possible. 4. Position the remaining wires on terminals 1-2-3 and tighten the screws. 5. Fix the power supply cable in place by fastening the GB 13 GB GB cable clamp screw. 6. Close the terminal board cover by tightening the screws V. Connecting the supply cable to the mains Install a standardised plug corresponding to the load indicated on the data plate located on the appliance. The appliance must be directly connected to the mains using an omnipolar circuit-breaker with a minimum contact opening of 3 mm installed between the appliance and the mains. The circuit-breaker must be suitable for the charge indicated and must comply with current electrical regulations (the earthing wire must not be interrupted by the circuit-breaker). The supply cable must be positioned so that it does not come into contact with temperatures higher than 50°C at any point. Before connecting the appliance to the power supply, make sure that: • The appliance is earthed and the plug is compliant with the law. • The socket can withstand the maximum power of the appliance, which is indicated by the data plate. • The voltage is in the range between the values indicated on the data plate. • The socket is compatible with the plug of the appliance. If the socket is incompatible with the plug, ask an authorised technician to replace it. Do not use extension cords or multiple sockets. ! Once the appliance has been installed, the power supply cable and the electrical socket must be easily accessible. ! The cable must not be bent or compressed. ! The cable must be checked regularly and replaced by authorised technicians only. ! The manufacturer declines any liability should these safety measures not be observed. We recommend cleaning the oven before using it for the first time, following the instructions provided in the „Care and maintenance” section. TECHNICAL DATA Oven dimensions (WxDxH) 38x34x39 cm Volume 50 l Useful measurements relating...
Ce manuel est également adapté pour les modèles :Plate - UA (1.31 mb)
Plate - K1E1 (1.31 mb)
Plate - R (1.31 mb)