Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
Your appliance is supplied with: Order no. . The following accessories can be obtained from a specialist dealer: Before Using Your Appliance for the First Time Time of day . Before you use your appliance for the first time, it is necessary to set the current time on the electronic timer. . After connecting to the mains, or after a power failure, the display {:{{ will blink. Setting the time: Setting the time of day: 1. Press the middle of the rotary control so that it pops out. 2. Press the + button for setting the time of day. . The arrows above the rotary control flash. Note: The time cannot be set if an automatic function is active (see Electronic clock for cancelling automatic function). 3. Turn the rotary control to set the time of day (e.g. |A:{{ Uhr). . The time setting has been programmed as soon as the light illuminating the arrows above the rotary control goes out. Acknowledgement signal . It is possible to set the appliance so that an acknowledgement signal is heard every time a button is pressed. To activate the signal: . The rotary control must be pressed in. 1. Press the v and 0 buttons simultaneously for approx. 10 seconds until A|| appears in the display. 2. Press any of the buttons to confirm the setting. To cancel the signal: . The rotary control must be pressed in. 1. Press the v and 0 buttons simultaneously for approx. 10 seconds until A{{ appears in the display. 2. Press any of the buttons to confirm the setting. Preliminary cleaning: 1. Clean the appliance exterior with a soft moistened cloth. 2. Clean the oven and the accessories with a hot detergent solution. . Please observe the operating instructions furnished with the hob. Initial burn-in: 1. Heat the empty oven for approx. 30 minutes. Select top and bottom heat at a setting of 240° C. During the initial burn-in phase, please open the kitchen windows to dissipate unpleasant odours. 2. Operate cast-iron hotplates, without placing utensils on them, on the highest heat setting for about 1 to 2 minutes. The odour rising from the hotplates is caused by the burning-in of the corrosion protection, and occurs only during the initial use. Cooking Operating the hotplates . The hotplates and the oven functions can be locked (see ”Safety devices” section). This feature prevents the cooker from being unintentionally switched on, e.g. by children. . Important: Separate operating instructions are enclosed with the hob. These operating instructions contain important information concerning operation of the hob. Please read thoroughly before using the hob for the first time. The heat setting can only be selected while the arrows above the rotary control are flashing. The hotplate switches on automatically after 3 seconds. . The selected heat setting is displayed above the switches. . The hotplates can be set from | to O, including intermediate settings which are identified by a dot (e.g. A•). Normal mode Switching ON: 1. Press the button for the desired hotplate. 2. Select the desired heat setting with the rotary control. . Information on preselected heat settings can be found in the Table of cooking times. Switching OFF: 1. Press the button for the desired hotplate. 2. Turn the rotary control back to {. . You can also use the button to switch off the hotplate by keeping it pressed until { appears in the display. Note: Alternatively you can adjust the heat setting by repeatedly pressing the appropriate hotplate button. rear left rear right front leftfront right Cooking Rapid boil mode . Rapid boil mode reaches the preselected heat setting quickly and at maximum power. Electronic rapid boil function 1. Press the button for the desired hotplate. 2. Select the simmer setting (e.g. }•). 3. Press the „U” button. The „U” is now displayed, alternating with the heat setting. . When the „U” goes out, the electronic automatic rapid boil control is complete and the hotplate switches back to the simmer setting (e.g. }•). . To stop the electronic rapid boil function, switch off the hotplate. Dual-circuit cooking zones . The dual-circuit cooking zones depend on the connected hob. Important: Please read the operating instructions for your hob. . The left front and right rear dual-circuit cooking zones are switched on via the cooker. . The left rear and right front dual-circuit cooking zones are switched on via the hob. Switching on the dual circuit 1. Press the button for the desired hotplate. 2. Select the desired heat setting. 3. Press the o button. . To stop dual-circuit cooking, switch off the corresponding hotplate. Manual rapid boil mode 1. Press the button for the desired hotplate. 2. Turn the rapid boil switch to Setting O. 3. When the boiling point has been reached, press the corresponding button and switch back to the desired simmer setting with the rotary control. Cooking Table of cooking times Without rapid boil Melt Heat Fry With automatic rapid boil mode Steam Boil Braise Note: Examples (Cooking) chocolate Butter Gelatine Vegetables (tinned) Stew P...
Ce manuel est également adapté pour les modèles :Plate - E1693N2/05 (1.41 mb)