Évaluations - 1, GPA: 4
(
)
)
|
Facilité d'utilisation
Otherwise, insert the protective plate into a groove at a slightly higher angle and make sure that it engages in the retainers. 4. Close the oven door so that it touches the protective plate. 5. Press the function selector and turn it clockwise to the # grill setting. 6. Keeping the function selector pressed, push the 8 ignition button. 7. The gas escaping from the gas grill is ignited using the ignition button. To activate the safety pilot, press and hold the function selector for 10 seconds. The safety pilot is activated. If the gas flame goes out, the gas supply is automatically interrupted by the safety pilot. 8. Check that the flame is lit. If it is not, repeat the process from step 5. 9. When the dish has finished cooking, switch the function selector off. Once the oven has cooled down, remove the protective plate again. : Caution! The ignition device should not be actuated for more than 15 seconds. If the burner does not light within 15 seconds, wait for at least one minute. Then repeat the ignition process. Setting the timer You can use the timer as a kitchen timer. It runs independently of the oven. The timer has a special signal. This means that you can tell whether the timer or cooking time has expired. Setting procedure 1. Press the 0 Clock button. The S timer symbol flashes. 2. Use the + or - button to set the timer time. + button / default value = 10 minutes - button / default value = 5 minutes The timer starts after a few seconds. The S symbol appears in the display. The elapsed time is shown. The time has elapsed Care and cleaning With attentive care and cleaning, your hob and oven will retain its looks and remain in good working order for a long time. We will explain here how you should care for and clean them correctly. Notes ¦ Slight differences in the colours on the front of the oven are caused by the use of different materials, such as glass, plastic and metal. ¦ Shadows on the door panel which look like streaks, are caused by reflections made by the oven light. ¦ Enamel is baked on at very high temperatures. This can cause some slight colour variations. This is normal and does not affect operation. The edges of thin trays cannot be completely enamelled. As a result, these edges can be rough. This will not impair the anti-corrosion protection. Upper glass cover Before opening the top cover, remove any spills with a cloth. Use glass cleaner if possible. For cleaning, remove the top cover. To do this, hold the cover securely on both sides with both hands and pull it upwards. A signal sounds. Press the 0 Clock button. The timer display goes out. Changing the timer duration Press the Clock button. Use the + or - button to change the time. Cancelling the setting Press the 0 Clock button. Press the - button repeatedly until a zero appears in the display. The timer and cooking time count down at the same time The symbols light up. You can see the timer time counting down in the display. To query the x remaining time: Press the 0 button. The queried value appears in the display for a few seconds. If the cover hinges become loose, note the letters marked on them. The hinge with the letter R must be fitted on the right, and the hinge with the letter L must be fitted on the left. After cleaning, re-assemble the top cover following the same procedure in reverse order. Only close the top cover once the burners have cooled down. Cleaning agents Damage to the various different surfaces caused by using the wrong cleaning agent can be avoided by observing the following instructions. When cleaning the hob do not use ¦ undiluted washing- up liquid or dishwasher detergent, ¦ scouring pads, ¦ abrasive cleaning agents such as oven cleaner or stain remover, ¦ high-pressure cleaners or steam jets. ¦ Do not clean individual parts in the dishwasher. When cleaning the oven do not use ¦ sharp or abrasive cleaning agents, ¦ cleaning agent with a high alcohol content, ¦ scouring pads, ¦ high-pressure cleaners or steam jets. ¦ Do not clean individual parts in the dishwasher. Wash new sponges thoroughly before first use. Stainless steel Wipe with some washing- up liquid and a damp cloth. Always wipe parallel to the natural grain. Otherwise, fronts you may scratch the surface. Dry with a soft cloth. Remove flecks of limescale, grease, starch and albumin (e. g. egg white) immediately. Do not use any abrasive materials, scouring sponges or rough cleaning cloths. The stainless steel fronts can be polished using a special care product. Follow the manufacturer's instructions. You can purchase special stainless steel cleaner from our after- sales service or from specialist retailers. Enamel surfaces and Clean with some washing- up liquid and a damp cloth. Dry with a soft cloth. lacquered surfaces Burners and steel Do not clean in the dishwasher. Remove the wire rack and clean with a sponge, washing- up liquid and grid of the gas burn- some hot water. Remove the burner cup and cap. Clean with a sponge and some hot water and w...