Log:
Évaluations - 3, GPA: 4.3 ( )

Instructions Brinkmann, Modèle 842-0200-0

Fabricant : Brinkmann
Taille : 537.79 kb
Nom Fichier : b624e3d6-e24f-1aa4-1954-d83b1a640896.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


• Propane cylinder should remain upright to prevent liquid propane flare-up. • DO NOT connect to a remote gas supply such as natural gas or a refillable propane cylinder. • In case of fire, turn gas "OFF" at burner control knobs and use Type 'BC' fire extinguisher or other appropriate means to extinguish flame. • Keep hands, face and hair away from burners. Use long matches or long-nosed lighter to light the burners. DO NOT wear loose clothing or allow long hair to hang freely while lighting or using stove. • Always snap down legs to form a "V" with the stove base to prevent the stove from becoming unstable while in use. Use only on a flat surface • DO NOT move stove while in use. Avoid touching hot surfaces. • Use only supplied regulator TYQ-8A (Brinkmann part number 450-TYQ8-A). • Only use replacement/accessory parts manufactured by The Brinkmann Corporation. Repairs should be performed by The Brinkmann Corporation. For parts or repairs contact The Brinkmann Corporation’s Customer Service Department at 1-800-527-0717. • Properly dispose of all packaging materials. 842-0200-0_Camp Stove-SS.qxd 3/17/03 4:53 PM Page 4 ASSEMBLY INSTRUCTIONS READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING OR OPERATING YOUR STOVE. Inspect contents of the box to ensure all parts are included and undamaged. FOR MISSING PARTS, PLEASE CALL CUSTOMER SERVICE AT 1-800-527-0717. (Proof of purchase will be required.) Step 1 Snap down legs to form a "V" with the stove base. Step 2 Open lid and align the two wind guards by inserting notched support arms into wind guards. Step 3 Remove regulator assembly from under grill inside stove. Replace grill. Make sure burner control knobs are in "OFF" position. Step 4 Attach regulator assembly to stove fitting. HAND TIGHTEN ONLY. Do not cross-thread connections. Step 5 Attach propane cylinder to regulator assembly by turning propane cylinder counter-clockwise. HAND TIGHTEN ONLY. Do not cross-thread connections. CAUTION: Turn cylinder so that it is fully upright. The cylinder must always sit flat on surface. See diagram below. Step 6 Follow "Gas Leak Testing" instructions on page 4 of this manual. 2–3" NOTE:Propane canister should be positioned a minimum of 2–3" from stove. Always use a canister with a flat bottom. Cooking Grill Notched Support ArmRegulator Assembly Burner Control Knobs WARNING: Always snap down legs to form a "V" with the stove base to prevent the stove from becoming unstable while in use. Attach Detach Counter-Clockwise Clockwise 3 842-0200-0_Camp Stove-SS.qxd 3/17/03 4:53 PM Page 5 GAS LEAK TESTING WARNING • • • • Gas leak testing must be performed outdoors in a well ventilated area every time cylinder is connected to stove. Always keep unit away from open flames, sparks or lit cigarettes. Never use a flame to check for gas leaks. Never use a unit that has a gas leak. Contact The Brinkmann Corporation’s Customer Service Department for replacement parts or repairs at 1-800-527-0717. Stove Fitting Regulator Assembly Regulator Watch for Bubbles Step 1 Assemble stove per "Assembly Instructions" on page 3 of this manual. Make sure burner control knobs are in "OFF" position. Step 2 Prepare a soapy water solution (one part dishwashing liquid to three parts water) to test for gas leaks in the connections. Apply a generous amount of the soapy mixture to the regulator assembly at the regulator, along entire length of hose, and at the stove fitting (located on the right side of stove). Step 3 With the burner control knobs in the "OFF" position, check for bubbles where propane canister attaches to regulator assembly, along entire length of hose, and at stove fitting. If soapy mixture starts bubbling, gas is leaking through the connections. Disconnect the propane canister. Retighten the connection that is leaking gas. Repeat procedure with soapy mixture until gas no longer leaks. NEVER USE A FLAME TO CHECK FOR GAS LEAKS. Step 4 Once all gas leaks have been sealed, WAIT AT LEAST 5 MINUTES FOR GAS FUMES TO DISSIPATE BEFORE LIGHTING THE BURNERS. Carefully follow "Operating Instructions" to light the burner and properly operate this unit. 4 842-0200-0_Camp Stove-SS.qxd 3/17/03 4:53 PM Page 6 OPERATING INSTRUCTIONS READ ALL SAFETY WARNINGS AND INSTRUCTIONS CAREFULLY. WARNING • • DO NOT allow gasoline or other flammable vapors or liquids to come in contact with stove while lighting or at any time during use of stove. DO NOT allow the gas hose to come into contact with any hot surfaces. Inspect the hose for damage such as burns, chafing, and kinks before each use. Step 1 Make sure "Gas Leak Testing" from page 4 was completed and the burner control knobs are in the "OFF" position and stove is on a flat surface away from combustible material. Step 2 Decide which burner to light first. Using a long match, hold the flame beside burner. Turn the burner control knob SLOWLY counter-clockwise until the burner lights. WARNING: If the burner does not light within 5 seconds, turn t...


Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories