Évaluations - 1, GPA: 5 ( )

Fabricant : Jackson Taille : 6.45 mb Nom Fichier : Langue d'enseignement:

Shipped with Cover Plate. 44 [1121mm] Base Unit Prewash 36 [914mm] 96 [2441mm] 80 [2035mm] Front View 751 2 [1921mm] 601 4 [1529mm] 623 4 [1592mm] 29 [735mm] 101 10 [254mm] 4 [260mm] 6 [152mm] G A B 41 [1042mm] C 231 2 [598mm] 24 [611mm] G 42 [1069mm] 4 [102mm] Drive Unit F D E 8 [203mm] 41 [1041mm] 38 [965mm] 7 [178mm] Right Side Legend A - Machine water inlet 3/4" NPT, 180°F Hi-temp,140°F Low-temp minimum B - Electrical connection C - Drain connection 1-1/2" NPT D - Vent collar - Optional E - Vent cowl standard F - Prewash water inlet 3/4" NPT 110°F-140°F G - Cold water thermostat plumbing connection 3/4" NPT - Optional H - Steam electrical connection J - 1" NPT Steam connection K - 3/4" Condensate connection L - 3/4" NPT Incoming 110°F water connection M - 3/4" NPT 180°F water to dishmachine. Note: All vertical dimensions are +/- 1/2" from floor due to adjustable bullet feet. H J L M K F 38 [966mm] 111 4 [285mm] 131 2 [345mm] 233 4 [604mm] 41 4 [110mm] 53 4 [148mm] 81 2 [218mm] 61 4 [159mm] 121 2 [316mm] F J H L M 43 [1092mm] 171 2 [445mm] 61 2 [162mm] 111 2 [295mm] 153 4 [400mm] 161 2 [417mm] SECTION 1: SPECIFICATION INFORMATION AJ-80T STEAM - RIGHT TO LEFT 21 AJ-44T Series Technical Manual 7610-003-07-21 Issued: 03-21-2006 Revised: 09-29-2007 SECTION 1: SPECIFICATION INFORMATION SIDE LOADER (LEFT TO RIGHT) DIMENSIONS NOTE: ALL DIMENSIONS ARE TYPICAL. 23” or 30” depending onthe width of the side loader. CONVEYORDISHWASHERLENGTH8” or 15” depending on thewidth of the side loader. 4 1/2” MINIMUM 25” DISHWASHER 5” 12 1/2” 14 1/2” 29” 1 1/2” TABLEROLL 20 3/4”OPENING1” A A 1/2” MINIMUM 1/2” DISHTABLE USE SILICONE BETWEEN TABLE AND LIP OF SIDE LOADER TO PREVENT LEAKAGE. WALL OF SIDE LOADER SECTION “A-A” CENTER-LINE DISHMACHINE SPLASH SHIELD VENT CONNECTION OPENING 1 1/2” DRAIN. CONNECTED TO DISHMACHINE DRAIN LINE CONVEYOR DISHMACHINE AJ-44T Series Technical Manual 7610-003-07-21 Issued: 03-21-2006 Revised: N/A 22 SECTION 1: SPECIFICATION INFORMATION SIDE LOADER (RIGHT TO LEFT) DIMENSIONS DISHTABLE NOTE: ALL DIMENSIONS ARE TYPICAL. 14 1/2” 29” 8” or 15” depending on thewidth of the side loader. 23” or 30” depending onthe width of the side loader. CONVEYORDISHMACHINELENGTH 4 1/2” MINIMUM 12 1/2” 25” DISHWASHER 5” 1 1/2” TABLE ROLL 20 3/4”OPENING 1” 1/2” MINIMUM 1/2” WALL OF SIDE LOADER USE SILICONE BETWEEN TABLE AND LIP OF SIDE LOADER TO PREVENT LEAKAGE SECTION “A-A” CONVEYOR DISHMACHINE CENTER LINE DISHMACHINE VENT CONNECTION OPENING SPLASH SHIELD AA 1 1/2” DRAIN. CONNECTED TO DISHMACHINE DRAIN LINE AJ-44T Series Technical Manual 7610-003-07-21 Issued: 03-21-2006 Revised: N/A 23 SECTION 1: SPECIFICATION INFORMATION SIDE LOADER (INSTALLED) DIMENSIONS 23” SIDE LOADER DIMENSIONS MODEL DIMENSIONS AJ-44T 75” AJ-66T 97” AJ-80T 111” (Left to Right installation shown for reference.) 30” SIDE LOADER DIMENSIONS MODEL DIMENSIONS AJ-44T 82” Refer to chart above. 34” 23” or 30” depending on the width of the side loader. 10” 4” AJ-66T AJ-80T 104” 118” NOTE: ALL DIMENSIONS ARE TYPICAL. AJ-44T Series Technical Manual 7610-003-07-21 Issued: 03-21-2006 Revised: N/A 24 SECTION 2: INSTALLATION & OPERATION INSTRUCTIONS 25 NOTE: THE INSTRUCTIONS PROVIDED HEREIN, UNLESS OTHERWISE SPECIFIED ARE FOR THE DISHMACHINES ONLY. THERE ARE SEPARATE DIRECTIONS FOR THE GAS BOOSTER. VISUAL INSPECTION: Before installing the unit, check the container and machine for damage. A damaged container is an indicator that there may be some damage to the machine. If there is damage to both the container and machine, do not throw away the container. The dishmachine has been inspected and packed at the factory and is expected to arrive to you in new, undamaged condition. However, rough handling by carriers or others may result in damage to the unit while in transit. If such a situation occurs, do not return the unit to Jackson; instead, contact the carrier and ask them to send a representative to the site to inspect the damage to the unit and to complete an inspection report. You must contact the carrier within 48 hours of receiving the machine. Also, contact the dealer through which you purchased the unit. UNPACKING THE DISHMACHINE: The machine should be unboxed and removed from shipping pallet prior to being installed. Open the front door and remove all of the packing materials. Once unpacked, ensure that there are no missing parts from the machine. This may not be obvious at first. If it is discovered that an item is missing, contact Jackson immediately. LEVEL THE DISHMACHINE: The dishmachine is designed to operate while being level. This is important to prevent any damage to the machine during operation and to ensure the best results when washing ware. The unit comes with adjustable bullet feet, which can be turned using a pair of channel locks or by hand if the unit can be raised safely. Ensure that the unit is level from side to side and from front to back before making any connections. You will be able to adjust the overall height of the unit by turnin...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :