Évaluations - , GPA: ( )

Instructions Frigidaire, Modèle 200 Series

Fabricant : Frigidaire
Taille : 643.83 kb
Nom Fichier :

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Low water pressure may occur when laundryor showers are in operation. Wait until wateruse is reduced before starting dishwasher. Water Temperature Hot water is needed for best dishwashing anddrying results. Water entering dishwasher should be at least 120°F (49°C) to givesatisfactory results. To check water temperature entering dishwasher: • Turn on hot water faucet nearest dishwasher for several minutes to clear cool water from pipes. • Hold a candy or meat thermometer instream of water to check the temperature. • If temperature is below 120°F (49°C), have a qualified person raise the hot water heaterthermostat setting. Important: Before starting a cycle, run hot water to clear cool water from pipe. The HEAT DRY option in combination with rinse aid will give you excellent drying results. The energy to use HEAT DRY costs pennies per cycle. You may turn off the HEAT DRY option, however you will have items in your dish load that will not be dry at the end of the cycle. 10 Care and Cleaning Allow heating element to coolbefore cleaning the interior. Failure to do so can result in burns. Burn Hazard Outside—Occasionally wipe with a mildnonabrasive detergent and water. Rinse and dry. Models with Stainless Steel Door— Clean outer door with warm soapy water and a dishcloth or sponge. Rinse with clean water and a dry cloth. Do not use harsh cleaners. Inside—The inside of the dishwasher is self- cleaning with normal use. If needed, cleanaround the tub gasket area with a damp cloth. The filter is self-cleaning. A glass trap located in the center of the filter is designed tocollect pieces ofbroken glass, straws, bones and pits. Toremove items in glass trap, grasp handle, lift out, emptyand replace. Note: Hard water may cause lime deposit buildup on the interior of the dishwasher. Forcleaning instructions see “Removing Spotsand Film” section. Overfill Protector—keeps dishwasherfrom overfilling and is located in the left frontcorner of the tub. • Clean occasionally with household cleanercontaining vinegar or bleach to dissolve anybuildup. • Overfill Protector should move up anddown freely about one inch. If it does not move, lift and clean underneath. Care of Drain Air Gap If a drain air gap was installed for your built-indishwasher, check to make sure it is clean so the dishwasher will drain properly. A drain air gap is usually mounted on countertop and canbe inspected by removing the cover. This is notpart of your dishwasher and is not covered by warranty. Freezing temperatures may cause water lines to rupture. Be sure all supply lines toand circulating lines within dishwasher areprotected. Failure to do so could result in propertydamage. Property Damage Hazard Winterizing A dishwasher left in an unheated place shouldbe protected from freezing. Have a qualified person do the following: To Disconnect Service: 1. Turn off electrical power to the dishwasherat the supply source by removing fuses or tripping circuit breaker. 2. Shut off water supply. 3. Place a pan under the inlet valve. Disconnect water line from inlet valve and drain into pan. 4. Disconnect drain line from pump and drain water into pan. Note: See Installation Instructions for more details. To Restore Service: 1. Reconnect the water, drain, and electrical power supply. 2. Turn on water and electrical power supply. 3. Fill both detergent cups and rundishwasher through a NORMAL cycle. 4. Check connections to make sure they do not leak. Note: See Installation Instructions for more details. 11 Solutions to Common Dishwashing Problems Before calling for service, review this list. Itmay save you both time and expense. Thislist includes common experiences that arenot the result of defective workmanship or material in your dishwasher. Food Soils Left on Dishes • Choose another cycle for longer washingtime. • Check rack loading section for properloading—avoid nesting items. • Home water pressure may be too low— should be 20 to 120 pounds per square inch (psi). • Check incoming water temperature. Itshould be at least 120°F (49°C). (See Factors Affecting Performance.) • Select HI-TEMP WASH option. • Check water hardness. For extremely hard water, it may be necessary to install a watersoftener. (See Detergent Chart.) • Use fresh detergent. • Check to make sure funnel in top rack is not blocked. • Make sure items are not blocking the sprayarms, preventing them from rotating. Dishes not Dry • Select heat dry option. • Make sure the rinse aid dispenser is filled. • Increase the amount of rinse aid. (SeeRinse Aid.) • Check the incoming water temperature. Besure it is at least 120°F (49°C). • Check for proper loading—avoid nestingitems. • Plastic items may need to be towel dried. • Cups with a concave bottom will collect water. Glassware/Flatware Spotted or Cloudy • Check water hardness. For extremely hard water, it may be necessary to install a watersoftener. (See Detergent Chart.) • Water temperature may be low. Avoid extremely low or high temperatures. (SeeFactors Affec...