Évaluations - 3, GPA: 3.7
(
)
)
|
Photos et spécifications Indesit DI 620 |
Facilité d'utilisation
This appliance complies with the following EEC directives: - 73/23/EEC (Low Voltage) and subsequent modifications; -89/336/EEC (Electromagnetic Compatibility) and subsequent modifications. -97/17/EEC (Labelling) 1.Carefully dispose of the packing material. 2.After removing the packing, check to make sure that the appliance is not damaged. If in doubt, contact a qualified professional. 3.The dishwasher must only be used by adults for the washing of household dishes and cooking utensils. 4.Fundamental rules to follow when using the appliance: -Never touch the dishwasher when barefoot or with wet hands or feet; -We discourage the use of extension cords and multiple sockets; -During installation, the power supply cord must not be excessively or dangerously bent or flattened; -If the appliance is not operating properly or maintenance must be performed, disconnect the appliance from the power supply. 5.Keep detergents out of the reach of children, who must also be kept away from the dishwasher when it is open. 6.This appliance cannot be installed outdoors, not even if the area in which it is installed is covered by a roof; it is also very dangerous to leave it exposed to the rain and elements. 7.Do not touch the heating element during or after a wash cycle. 8.Do not lean or sit on the door when it is open, as this could overturn the dishwasher. 9.If the appliance malfunctions, turn off water supply to the appliance and disconnect the plug from the wall socket. Then, consult the section entitled, "Troubleshooting." If you cannot resolve the problem, contact a service centre. 10.Appliances which are no longer being used must be made inoperable by cutting the power supply cord and removing the door lock. To maintain the EFFICIENCY and SAFETY of this appliance, we recommend: • call only the Service Centers authorized by the manufacturer • always use original Spare Parts Close-up View (control panel) 1 2 3 4 CP BA ON-OFF Button P Cycles Indicator Lights ON - OFF Light Cycle select button 1 GB Close-up View (Interior) J L K H F E G I Upper Rack Bottom Sprayer Arm Top Sprayer Arm Salt Container Cap Rack Height Adjustor Washing Filter Lower Rack Detergent and Rinse Aid Dispenser Technical characteristics Width cm. 59,5 Depth cm. 57 Height cm. 82 Capacity 12 standard place settings Mains water pressure 4,3 psi - 145 psi (30 KPa. 1MPa )(0,3 .10 bar) Power voltage See data plate Total absorber power See data plate Fuse See data plate GB 2 Salt ....... Salt The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes and utensils. The appliance is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the water. Loading the Salt into the Softener Always use salt intended for use with dishwashers. The salt container is located beneath the lower rack and should be filled as follows: 1. Remove the lower rack and then unscrew and remove the cap from the salt container; 2. If you are filling the container for the first time, fill it with water; 3. Place the end of the funnel (supplied) into the hole and introduce about 2 kg of salt. It is normal for a small amount of water to come out of the salt container. 4. Carefully screw the cap back on. Low Salt Indicator This green device is located at the centre of the cap for the decalcification cartridge and it indicates whether the container is full. When the indicator is not visible it means that the supply of salt must be replenished . To prevent the formation of rust, load the salt just before beginning a wash cycle. Adjusting Salt Consumption The dishwasher is designed to allow for adjusting the amount of salt consumed based on the harness of the water used. This is intended to optimize and customize the level of salt consumption so that it remains at a minimum. Your Local Water Board can supply the degree of hardness of the water in your area. To adjust salt consumption, proceed as follows: 1) Unscrew the cap from the salt container. 2) There is a ring on the container with an arrow on it (see figure to the side), if necessary, rotate the ring in the anti- clockwise direction from the "_" setting towards the "+" sign, based on the hardness of the water being used. It is recommended that adjustments be made in accordance with the following schema: Water Hardness Clarke degrees °fH mmol/l Selector position Salt consumption (grams/cycle) Autonomy (cycles\2kg) 0 - 14 0 - 17 0 -1,7 / 0 / 14 - 36 18 -44 1,8 - 4,4 "-" 20 60 36 - 71 45 -89 4,5 - 8,9 MED 40 40 >71 > 89 > 8,9 "+" 60 25 3 GB Detergent and Rinse Aid .... Detergent Detergent specifically intended for use with dishwashers must be used. The dispenser mus...