Évaluations - 3, GPA: 5 ( )

Fabricant : Eurotech Appliances Taille : 893.36 kb Nom Fichier : 8cc92d27-410f-49b5-b813-61cceb00575a.pdf Langue d'enseignement:

When moving the appliance into or out of the cabinet, be careful not to damage the power-supply cord. WARNING! Before working on wiring for any electrical appliance, be sure the electrical power has been turned off at the breaker/fuse box. WARNING! Disconnect electrical power supply and place a tag at the disconnect switch indicating that you are working on the circuit. WARNING! Electrical and grounding connections must comply with the applicable portions of the national electrical code and/or other local electrical codes. GROUNDING INSTRUCTIONS WARNING! This appliance must be properly grounded. A) Grounding instructions for a grounded, cord-connected appliance In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. WARNING! Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or personnel if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. B) Grounding instructions for a permanently connected appliance: This unit must be grounded to operate properly. It must be connected to a grounded metal, permanent wiring system or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead of the appliance. ENGLISH ENGLISHENGLISHENGLISHENGLISHENGLISH 11 CONNECTING AN ELECTRIC CABLE If the cord is not long enough, or if a hard-wire installation is needed, follow the steps below to complete the electrical connection. WARNING! Before working on wiring for any electrical appliance, be sure the electrical power has been turned off at the breaker/fuse box. Toe kick bracket 1. Remove the access panel by first removing the two Phillips screws that secure the panel to the unit. Opening the dishwasher door may make it easier to get access to these screws. 2. Remove the toe kick brackets by holding the small metal spring tab on the outer edge of the base pan toward the outside of the machine. Continue holding the tab as you pull straight out on the bracket. (Note: It may be stubborn because it’s in guide slots on the base pan.) See page 10 for instructions on how to adjust the toe kick brackets. 3. Remove the guard plate by removing the three phillips-head screws that hold the guard plate in place, one in the middle top, and one each in the lower left and right side. After the screws are removed, grip the bottom of the guard plate and pull it toward you to remove it. You can now access the inlet valve and terminal block. 4. Remove the supplied power cord. 5. Connect supply cable with a UL-listed strain relief bushing (if nonmetallic cable is to be used). 6. Connect branch circuit white lead to white lead on main terminal block, as illustrated at right. Making the Connection 7. Connect branch circuit black lead to brown lead on main terminal block, as illustrated. 8. Connect ground wire to ground on terminal block, as illustrated. 9. Replace the guard plate. 10. Replace the toe kick brackets and toe kick (see page 9). TESTING FOR LEAKS 1. Turn on the water supply and check for leaks. 2. Turn the power on at breaker/fuse box and test the dishwasher operation by running a Soak and Hold cycle (This should take about ten minutes.) 3. Turn off the electrical power and check for leaks under the dishwasher and sink. 4. Make sure that no kinks have developed in the drain lines. If there are no leaks and the dishwasher seems to be working properly, continue with the installation. FITTING THE EDW294E ONE-PIECE CUSTOM DOOR PANEL Model EDW294E can only be installed with a one-piece custom door panel that extends from the toe kick to the counter top. The unit comes with everything needed to make installing the door panel easy. The door is predrilled for the panel’s mounting screws. To order a one-piece door, contact your dealer. The part numbers are listed below: White 750163400 Black 750163600 Bisque 750163700 Stainless Steel 750163800 ITEMS PROVIDED WITH THE ONE-PIECE DOOR PANELS These items are supplied with the doors: < One-piece door < Color-coordinated toe kick < Door handle < Handle support bracket < Two 1/2” machine screws for handle < Two 1/2” sheet metal screws for toe kick INSTALLING THE ONE-PIECE CUSTOM DOOR PANEL Before fitting the custom panel, the dishwasher must be installed underneath the cabinet. For this installation, we recommend that you install the 2” fill strip (see page 6) that comes with the unit to hide the top of the dishwasher and further reduce water ...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :