Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
·Hygiene * The temperature is increased during the cleaning process. This increases the hygiene status. This additional option is ideal for cleaning e.g. chopping boards and baby bottles. IIntensive zone * Perfect for a mixed load. You can wash very soiled pots and pans in the lower basket together with normally soiled utensils in the upper basket. The spray pressure in the lower basket is intensified, the rinsing temperature is increased slightly. .Extra drying * An increased temperature during the final rinse and an extended drying phase ensure that even plastic parts dry better. There is a slight increase in the energy consumption. Washing the dishes Aqua sensor * * depending on model The Aqua sensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water. The Aqua sensor is used according to the programme. If the Aqua sensor is active, “clean” rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 3–6 litres. If the turbidity is greater, the water is drained and is replaced with fresh water. In the automatic programmes the temperature and running time can also be adjusted to the degree of soiling. Switching on the appliance – Turn on the tap fully. – Open the door. – Switch on ON/OFF switch (. The display of the last selected programme flashes. This programme remains selected if no other programme button 0 is pressed. The expected programme duration flashes on the digital display 8. – Press the START button h. – Close the door. The programme starts running. Remaining running time display When the programme is selected, the remaining running time of the programme is indicated on the digital display 8. The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme). aus Display window Apart from information on the programme sequence, the display window )* also indicates additional information on e.g. spray pressure. If you would no longer like to have this additional information displayed, proceed as follows. – Open the door. – Switch on ON/OFF switch (. – Hold down programme button # and press START button h until the digital display 8 s:‹... is indicated. – Release both buttons. – Press programme button # until the factory set value ’:‹‚ is indicated on the digital display 8. To change the setting: – By pressing the 3 button, you can switch the on board computer (additional programme information) off ’:‹‹ or on ’:‹‚. – Press START button h. The set value is saved. – Close the door. Timer programming You can delay the start of the programme in 1 hour steps up to 24 hours. – Open the door. – Switch on ON/OFF switch (. – Press the button X + until ‹‚ is flaching in the timer programming display P. – Press + or – button until the X displayed time corresponds with your requirements. – Press START button h, timer programming is activated. – To delete timer programming X, press the + or – button until ‹‹ is indicated on the digital display P. You can change your programme selection at any time until the programme starts. – Close the door. End of programme The programme has ended when the value ‹:‹‹ is indicated on the numerical display 8. The end of the programme is also indicated by an acoustic signal. This function can be changed as follows: – Open the door. – Switch on ON/OFF switch (. – Hold down programme button # and press START button h until s:‹.... is indicated on the digital display. – Release both buttons. – Press programme button # until the factory set value ›:‹. is indicated on the digital display 8. To change the setting: – Press programme button 3. Each time the button is pressed, the set value increases by one level; when the value of ›:‹„ has been reached, the display jumps back to ›:‹‹ (off). – Press START button h, the set value is saved. – Close the door. Switching off automatically after the end of the programme To save energy, the dishwasher is switched off 1 minute after the programme ends (factory setting). Automatic disconnection can be adjusted from .:‹‹ to .:‹.. .:‹‹ Appliance does not switch off automatically .:‹‚ Off after 1 min .:‹. Off after 120 min – Open the door. – Switch on ON/OFF switch (. – Hold down programme button # and press START button h until s:‹... is indicated on the digital display. – Release both buttons. – Press programme button # until the factory set value .:‹‚ is indicated on the digital display 8. aus To change the setting: – Press programme button 3. Each time the button is pressed, the set value increases by one level; when the value of .:‹. has been reached, the display jumps back to .:‹‹ (off). – Press START button h. The set value is saved. – Close the door. Switching off the appliance Short time after the end of the programme: – Open the door. – Switch off ON/OFF switch (. – Turn off the tap (not applicable if Aqua- Stop fitted). – Remove the utensils ...
Ce manuel est également adapté pour les modèles :Lave-vaisselle - SBU69T05AU/18 (2.26 mb)
Lave-vaisselle - SBU69T05AU/22 (2.26 mb)
Lave-vaisselle - SBU69T05AU/23 (2.26 mb)
Lave-vaisselle - SBU69T05AU/25 (2.26 mb)