Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
You will find the appropriate programme information in the introduction. en Washing dishes Reduce costs! If only a small number of dishes have been loaded into the dishwasher, selecting a programme that operates at the next lowest temperature will usually suffice. Programme data The stated programme data are based on standard operating conditions. The values can vary considerably according to: different amounts of dishes temperature of mains water supply pressure of mains water supply ambient temperature fluctuations in mains voltage machine-related factors (e.g. temperature, water volume, ...). Energy and water consumption is reduced by up to 1/4 when dishes are washed in the upper basket only. Water consumption values are based on a water hardness setting of 4. Switching ON the appliance Open water tap fully. Switch ON main switch 1 . The selection of the most recently selected programme light up. This programme will be performed unless another programme button 6 is pressed. Close the door. The programme starts automatically. End of programme The programme has come to an end when the PROGRAMME END indicator 3 and the indicator for the selected programme are both lit up. Apart from this, the end of the programme is indicated by a buzzer. This function can be changed as follows:– Hold down the function button C and switch on the main switch 1 . Function button C flashes. Each depression of function button C changes the buzzer in 4 stages (from off to loud). Switch off the main switch 1 . The setting is stored. Switching the dishwasher OFF Several minutes after the programme has ended: Open the door when the programme has ended. Set main switch 1 to OFF. Turn the water tap off. (Does not apply when Aqua-Stop unit has been fitted) Remove dishes, etc. when they have cooled down. en Programme interruption Carefully open the door, it could happen that water splashes out of the appliance. Only open completely when the spray arm no longer turns. If the programme is already in “drying” mode, an acoustic signal reminds you to close the appliance door or to abort the programme. Switch OFF the main switch 1 . Indicator light goes out. The programme remains stored. If warm water is connected or if the machine is already heated up and the appliance door has been opened, leave the door slightly ajar, then close it, otherwise the appliance door can jump open through the expansion. In order to continue the programme flow, switch the main switch ON again and close the door. Cancel programme (Reset) Only when the master switch is ON. Press the A and C programme buttons simultaneously and hold them pressed for approx. 3 sec. The programme continues for approx. 1 min. The PROGRAMME END indicator and the indicator for the programme that has just been terminated light up. Set main switch 1 to OFF. Close the detergent compartment 30 . To restart the dishwasher, set main switch to ON again and select desired programme. Changing the programme It is possible to change the programme selection after you have switched the dishwasher on, provided that you have not yet closed the door. If it is necessary to change the programme after this, the programme cycle that has already begun (e.g. washing) will still carry on to the end. Maintenance and care You can help prevent faults by checking and maintaining your appliance regularly. This will save time and reduce problems. Therefore you should occasionally examine the inside of your dishwasher. Overall condition of the appliance Check the rinsing compartment for grease and limescale deposits. If you find any deposits: Fill the detergent dispenser with detergent. Start the empty appliance with the programme which has the highest rinsing temperature. Clean the door seal: Wipe the door seal regularly with a damp cloth and remove any deposits. Dishwasher salt Check the LOW SALT indicator 4 or 24 . Top up with salt, if required. Rinse-aid Check the LOW RINSE-AID indicator 5 on the front panel or the level indicator on the rinse-aid container 29 . Top up with rinse-aid, if required. Filters The filters 25 prevent larger remnants of food or other objects from getting inside the pump. This residue can occasionally clog up the filters. The filter system consists of a filter cylinder, a flat fine filter and, depending on the model, a microfilter (*). Inspect the filters for obstructions every time the dishwasher has been used. By unscrewing the filter cylinder, you can remove the filter system. Remove any food remnants and clean the filters under running water. en Reassembly: Insert the filter system and screw down with the filter cylinder. Spray arms Lime and remnants of food in the washing water can block the nozzles in the spray arms 22 and 23 and the arm mountings . Inspect the nozzles in the spray arms for blocked holes due to remnants of food. If necessary, pull the lower arm 23 upwards and lift it off. Unscrew the upper spray arm 22 . Clean both spray arms under running water. Refit the spray...
Ce manuel est également adapté pour les modèles :Lave-vaisselle - SE6CFE1GB/56 (1.95 mb)