Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
Keep children away from shipping carton and packaging components. Danger of suffocation from folding cartons and plastic film. General information Measures must be taken to ensure that built-under and built-in units that are subsequently re-sited as free-standing appliances cannot topple over. This can be achieved by bolting the dishwasher to the wall or fitting it under a continuous work surface which is screwed to the adjacent cupboards. Installation In order to function correctly the dishwasher must be properly installed. Specifications for the water intake and waste-water drainage, as well as electrical connections, must fulfil the criteria that are set out in the following paragraphs and the installation instructions. When installing the dishwasher, carry out tasks in the following order: – check contents of delivery upon receipt, – site dishwasher, – connect drainage hose, – connect inlet hose to water supply, – connect dishwasher to electricity supply. Checking contents of delivery All functions of your dishwasher have been thoroughly tested in the factory. A small number of water marks have been left on the dishwasher as a result. They disappear as soon as the appliance is used for the first time. Siting the dishwasher Dimensions associated with siting the dishwasher are contained in the installation instructions. Ensure that the appliance is completely level by adjusting the feet. Make sure that it is standing on a firm surface. Drainage connection See the installation instructions for details of procedure to be followed. If necessary, fit a siphon trap (U-bend) with a connecting piece for the drainage hose. Connect the drainage hose to the trap using the enclosed parts. aus Fresh-water connection Connect the inlet hose to a water tap using the enclosed parts and in accordance with the installation instructions. Water pressure: Minimum 0,05 MPa (0,5 bar) – maximum 1 MPa (10 bar). If the water pressure is higher, install a pressure reducing valve. Flow rate: Minimum of 10 litres per minute. Water temperature: We recommend cold water connection only. Electrical connection This appliance should only be connected to a 240 V AC source via a properly installed earthed socket. See nameplate for size of required fuse. The socket must be installed close to the dishwasher. If you need to extend the mains connecting lead, do not cut off the plug. Replace the whole cable, which can be disconnected at the junction box on the rear of the appliance. If the domestic wiring includes a residualcurrent- operated (FI) circuit-breaker, make sure that it bears the mark, as only this type conforms to the latest regulations Disconnecting the dishwasher Here too, it is important that tasks are carried out in the correct sequence: always unplug the appliance from the mains electricity first of all. Pull plug out of wall socket. Turn off water supply. Disconnect drain and water input hoses. Remove screws in underside of work surface. Detach base board, if fitted. Pull out appliance and carefully withdraw hoses at same time. Transporting the dishwasher Drain water from the dishwasher. Secure all loose parts. The appliance should only be transported in an upright position. If the appliance is not kept upright during transport, any water left inside may seep into the control module and cause subsequent errors with programme functions. The appliance must be drained in the following sequence: Turn on the tap. Close the door. Set main switch to ON. Select the B programme. The programme duration in minutes is shown in the numerical display. Wait for approximately 4 minutes. Terminate the programme by pressing A and C simultaneously. The time display changes to . Wait a further minute and then switch the appliance off. Turn off the tap. Protection from freezing temperatures If the appliance is installed in a location where there is a risk of freezing temperatures (e.g. in a holiday home), all water must be completely drained out of the interior (see “Transporting the dishwasher”). Turn OFF the tap, disconnect the supply hose and allow to drain. aus Subjekt to modification " #!# ## %%%"$"!# ...
Ce manuel est également adapté pour les modèles :Lave-vaisselle - SGV69A13AU/27 (1.49 mb)
Lave-vaisselle - SGV69A13AU/32 (1.49 mb)
Lave-vaisselle - SGV69A13AU/36 (1.49 mb)
Lave-vaisselle - SGV69A13AU/37 (1.49 mb)