Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
Power Scrub NSF Certified Auto Wash Eco Wash Regular Delicate Wash Quick Wash Rinse and Hold cycle time (min) 130 105-119 105-119 95-115 80 30 9 water consumption (l) 25.6 13.6-22.6 13.6-22.6 8.7-19.5 11.3 11.3 4.0 water consumption (gal) 6.8 3.6-6.0 3.6-6.0 2.3-5.2 3.0 3.0 1.0 wash temperature (°C) 71.1 54.4-65.6 54.4-65.6 50-55 50 45 wash temperature (°F) 160 130-150 130-150 122-131 122 113 rinse temperature (°C) 68.9 68.9 68.9 65-68.9 68.9 50 rinse temperature (°F) 156 156 156 149-156 156 122 Half Load or Top Rack Only Option cycle time (min) 110 99-110 95-105 75 water consumption (l) 17.9 10.5-15.9 8.7-14.9 10.9 water consumption (gal) 4.7 2.8-4.2 2.3-3.9 2.9 NOTE: Only sanitizing cycles have been designed to meet the requirements of 6 for soil removal and sanitization efficacy. There is no intention, either directly or indirectly, that all cycles have passed the sanitization performance test. 10 10 Operating the Dishwasher SHX4AP, SHX5AL, SHX6AP To start the dishwasher: • Open the door. Press the [ON/OFF] button. • One of the wash cycle LEDs will be flashing. You can now select a wash cycle. • Press the [<] or [>] button to select the desired wash cycle. • Press [START] (LED stops flashing) • Close the door to begin the cycle. NOTE: 1. Rinse Agent LED will be illuminated if the unit needs Rinse Agent. 2. If you close the door without pressing the start button the unit will beep. To cancel a cycle: • Open the dishwasher door just far enough to expose the control panel. Be careful of hot water splash out! • Press and hold the [START/RESET] button until the “Active” LED goes out. • The "Clean" and one other LED will be flashing. You are now in the options mode. • Press [>] to select the option you would like to adjust. If the "Clean" and "Rinse Agent" LEDs are flashing you can adjust the Rinse Agent settings. If the "Clean" and "Sanitized" LEDs are flashing you can set the Extra Dry Heat. To set the amount of Rinse Agent: NOTE: If your glasses have spots on them, you need more Rinse Agent. If your glasses have streaks, you need less Rinse Agent. Follow the prior instructions to enter options mode. With the "Clean" and "Rinse Agent" LEDs flashing: • Press the [<] button to change the amount of rinse agent dispensed. 0 LEDs flashing --> Rinse Agent dispenser is OFF 1 LED flashing --> Lowest amount of rinse agent 2 LEDs flashing --> Medium amount dispensed 3 LEDs flashing --> Highest amount of rinse agent • Press [START] to save your settings. To turn Extra Dry Heat on or off: WARNINGDepending on your model you will either have 4, 5 or 6 wash cycles. You could be seriously scalded if you allow hot water to splash out of the dishwasher. OPEN THE DOOR CAREFULLY during any wash or rinse cycle. Do not fully open the door until water noises have stopped. • Close the door and wait for about 1 minute for the dishwasher to drain. • The unit will beep when done draining. • Open the door and press the [ON/OFF] button. • You are now ready to start a new cycle. To enter the options mode (Rinse Agent setting, Extra Dry Heat, Cycle Completion Signal): • Door must be open. Press the [ON/OFF] button to turn the unit on. • One of the wash cycle LEDs will be flashing. • Press and hold down the [>] button, then press and release the [START/RESET] button. Now release the [>] button. With the "Clean" and "Sanitized" LEDs flashing: • Press the [<] button to turn Extra Dry Heat on or off. The wash cycle LEDs will illuminate when you press [<] button. 0 LEDs flashing --> Extra Dry Heat is OFF 1 LED flashing --> Extra Dry Heat is ON To set the Cycle Completion Signal: With the "Clean", "Sanitized" and "Rinse Agent" LEDs flashing: • Press the [<] button to change the cycle completion tone level. The wash cycle LEDs will illuminate when you press [<]. 0 LEDs flashing --> Cycle Completion Signal is OFF 1 LED flashing --> Low tone level 2 LEDs flashing --> Medium tone level 3 LEDs flashing --> Highest tone level • Press [START] to save your settings. Operating the Dishwasher SHE5AL, SHE4AP To start the dishwasher: • With door closed, press the [ON/OFF] button. • One of the wash cycle LEDs will be flashing. You can now select a wash cycle. • Press the [<] or [>] button to select the desired wash cycle. • Select the Half Load or Delay Start features if desired at this point. If you would like to delay the start time of the dishwasher press the [Delay] button until the desired delay time (3,6,9 hrs.) is displayed by the corresponding LED. • Press [START] to begin the cycle (wash cycle LED will stop flashing). NOTE: Rinse Agent LED will be illuminated if the unit needs Rinse Agent. Child Lock • After pressing [START] you can activate the Child Lock feature. • Press and hold down the [<] button until "Child Lock" LED illuminates. Light goes out when button is released. • Now any button you press (except ON/OFF) will not function and the "Child Lock" LED illuminates when you press any button. • To deactivate, press and hold the [<] button unt...
Ce manuel est également adapté pour les modèles :Lave-vaisselle - SHE4AP02UC/08 (2.69 mb)
Lave-vaisselle - SHE4AP02UC/09 (2.69 mb)
Lave-vaisselle - SHE6AP12UC/06 (2.69 mb)
Lave-vaisselle - SHE6AP12UC/07 (2.69 mb)