Évaluations - 0, GPA: 0
(
)
)
|
Par ce dispositif a également d'autres instructions :
Lave-vaisselle - SN56V595EU/50 (3.53 mb)
Lave-vaisselle - SN56V595EU/50 (3.6 mb)
Facilité d'utilisation
’ Onboard computer ’:‹‹ -’:‹‚ Selecting language The language in the display window )2 can be set from p:‹‚, to p:.„. German p:‹‚ (Deutsch) is the factory setting. Language Setting Deutsch p:‹‚ English p:‹. Francais p:‹„ Nederlands p:‹… Italiano p:‹† ............... p:‹‡ Espanol p:‹. Portugues p:‹‰ Svenska p:‹S Norsk p:‚‹ Suomi p:‚‚ Dansk p:‚. Turkce p:‚„ ... ......... p:‚… Polski p:‚† Cesky p:‚‡ Magyar p:‚. Hrvatski p:‚‰ Slovensko p:‚S Slovensky p:.‹ ......... ..... ... p:.‚ Romana p:.. q / Deutsch * p:.„ * depending on model To change the language: 1. Open the door. 2. Switch on ON/OFF switch (. 3. Hold down programme button # and press START button )" until the digital display 8 •:‹... is indicated. 4. Release both buttons. en Water softening system/Special salt 5. Press programme button # until the factory set value p:‹‚ is indicated on the digital display 8. “German” (Deutsch) is indicated in the display window )2. 6. Press programme button 3. Each time the button is pressed, the set value increases by one level; when the value of p:.„ has been reached, the display jumps back to p:‹‚ 7. Press START button )". The set value is saved. 8. Close the door. Display window The display window )2 shows the selected programme, the remaining running time, the programme sequence (in words and as a coloured progress bar) and the selected options. In addition, when there is low salt and/or low rinse aid, the number of rinse cycles still possible is indicated and the fault is stated in the event of faults. When the onboard computer is switched on (see corresponding chapter), further information is shown and the water and energy consumption is briefly displayed. + Water softening system/Special salt To ensure good washing results, the dishwasher requires soft water, i.e. containing low amounts of lime, otherwise white limescale will be deposited on the utensils and inner container. Tap water above 1.2 mmol/l must be softened. The water is softened with special salt (regeneration salt) in the water softening system of the dishwasher. The setting and therefore the required amount of salt depends on the degree of hardness of your tap water (see table). Setting The amount of salt dispensed can be set from •:‹‹ to •:‹.. Salt is not required at the set value •:‹‹. 1. Find out about the hardness value of your tap water. Your water utility company will help you with this. 2. Set value can be found in the water hardness table. 3. Open the door. 4. Switch on ON/OFF switch (. 5. Hold down programme button # and press START button )" until •:‹.... is indicated on the digital display. 6. Release both buttons. The LED for button # flashes and the digital display 8 displays the factory setting •:‹…. To change the setting: 1. Press programme button 3. Each time the button is pressed, the set value increases by one level; when the value of •:‹. has been reached, the display jumps back to •:‹‹ (off). 2. Press START button )". The chosen setting has now been stored. 3. Close the door. Water hardness table !!!"!!!!!!!!!!"!! Water softening system/Special salt en Using special salt Always refill with special salt immediately before switching on the appliance. This ensures that overrun special salt solution is immediately washed out and does not corrode the rinsing tank. 1. Open the screw-type cap of the compartment 1R. 2. Fill the tank with water (only required when switching on the appliance for the first time). 3. Then add dishwasher special salt (not table salt or tablets). The water is displaced and runs out. As soon as the low salt indicator H is lit on the fascia or is requested in the display window )2, salt should be topped up. * depending on model Using detergents with salt component If combined detergents with a salt component are used, salt can usually be omitted up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/ l). If the water hardness is over 21° dH, special salt must be used. . % . . # . . &. . . $ . . en Rinse aid Switching off salt refill indicator/water softening system If the use of combined detergents with a salt component impairs the low salt indicator H on the fascia or the text in the display window )2 (Enough salt for another x rinse cycles), the displays can be switched off. . Proceed as described under “Setting water softening system” and set the value to •:‹‹. The water softening system and salt refill indicator are now switched off. a Caution Never fill the salt dispenser with detergent. You will destroy the water softening system. , Rinse aid As soon as the low rinse-aid indicator P is lit on the fascia or is requested in the display window )2, rinse aid should be topped up. The rinse aid is required for stain-free utensils and clear glasses. Use only rinse aid for domestic dishwashers. Combined detergents with rinse-aid component may be used up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l) only. If the water hardness is over 21° dH, rinse aid must be used. 1...
Ce manuel est également adapté pour les modèles :Lave-vaisselle - SN56V595EU/73 (3.51 mb)