Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
You can change your programme selection at any time until the programme starts. End of programme The programme has ended when the End display ` is lit. The end of the programme is also indicated by an acoustic signal. The buzzer volume can be set in 4 stages. Accordingly 0, 1, 2 or 3 displays are lit (see water hardness table). Factory setting: 2. This function can be changed as follows: – Open the door. – Switch on ON/OFF switch (. – Hold down button > P and press START button h until the End display ` and salt refill indicator )* flash. – Release buttons. – Keep pressing button > P until the salt refill indicator )* and rinse aid refill indicator )" flash. – Release buttons. The refill indicators )* and )" flash and the displays # and + are lit (= Setting 2). The set buzzer volume can be heard. To change the setting, – Press the button < H until the required setting has been selected. – Press START button h. The displays go out. The selected setting is saved. – Close the door. Note To save energy, the dishwasher automatically switches off after 2 minutes after the end of the programme. Switching off the appliance Short time after the end of the programme: – Open the door. – Switch off ON/OFF switch (. – Turn off the tap (not applicable if Aqua- Stop fitted). – Remove the utensils when they have cooled down. a=Warning At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. Interrupting the programme – Open the door. – Switch off ON/OFF switch (. The LEDs go out. The programme is saved. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. – To continue the programme, switch on the ON/OFF switch ( again. – Close the door. en Terminating the programme (Reset) – Open the door. – Press START button h for approx. 3 sec. The Cleaning display X goes out. – Close the door. The remaining programme sequence lasts approx. 1 minute more. (Buzzer sounds.) – Open the door. – Switch off ON/OFF switch (. – Close the door. Changing the programme When the START button h has been pressed, the programme cannot be changed. The only way a programme can be changed is by Cancel programme (Reset). Intensive drying The final rinse uses a higher temperature which improves the drying result. The running time may increase slightly. (Caution if utensils are delicate!) – Open the door. – Switch on ON/OFF switch (. – Hold down button > P and press START button h until the End display ` and salt refill indicator )* flash. – Release buttons. – Keep pressing button > P until the salt refill indicator )* and “Check water supply” )2 flash. – Release buttons. The displays )* and )2 flash. To change the setting, – Press button < H until the display # is lit (Intensive drying on). – Press START button h. The displays go out. The setting is saved. – Close the door. Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Overall condition of the machine – Check spray arm for grease and limescale deposits. If you find such deposits: – Fill detergent dispenser with detergent. Start the appliance without utensils in the programme with the highest rinsing temperature. Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers. – Regularly clean door seal with a damp cloth. Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any consequential damage. Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces. Stainless steel appliances: To prevent corrosion, avoid using sponge cloths or wash them out thoroughly several times before using for the first time. a=Warning Never use other chlorinated household detergents! Health hazard! Special salt and rinse aid – Check the refill indicators )* and )". If required, refill salt and/or rinse aid. en Filters The filters 1R keep large foreign objects in the rinsing water away from the pump. These foreign objects may occasionally block the filters. The filter system consists of a coarse filter, a flat fine filter and a microfilter. – After each washing cycle check the filters for residue. – Unscrew filter cylinder as illustrated and take out filter system. –Remove any residue and clean filters under running water. –Re-install filter system in reverse sequence and ensure that the arrow marks are opposite each other after closing the filter system. Spray arms Limescale and contaminants in the rinsing water may block nozzles and bearings on the spray arms 1: and 1B. – Check...
Ce manuel est également adapté pour les modèles :Lave-vaisselle - SPV43E00EU/06 (1.51 mb)
Lave-vaisselle - SPV43E00EU/07 (1.51 mb)
Lave-vaisselle - SPV43E00EU/09 (1.51 mb)
Lave-vaisselle - SPV43E00EU/11 (1.51 mb)