Évaluations - , GPA: ( )

Instructions Moyer Diebel, Modèle RDW6015FI

Fabricant : Moyer Diebel
Taille : 815.98 kb
Nom Fichier : 36873297-0ad1-489d-9f53-18031de0833e.pdf

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

1. Switch the dishwasher ON. 2. Press programme button to choose the desired programme. 3. Immediately press the Delayed Start button (Fig.2-17), the delayed start indicator illuminates; the time remaining indicator (Fig.2-18) changes to ‘1’. 4. Press the Delayed Start button as many times as necessary until the numerical display shows the required delay. 5. To cancel the time delay setting, pressing the Delayed Start button until the delayed start indicator and time remaining indicator go out. 6. Close the door; the time remaining indicator will blink and start to count down. The programme will start when the delayed start indicator goes out and the wash cycle will begin. To cancel a delayed start programme in progress, follow the ‘Cancelling a programme in progress’ instructions. Fig.2-17 Fig.2-18 9 Fig.2-19 Fig.2-20 Fig.2-19 Fig.2-20 . Load Button This function allows the dishwasher to wash dishes using only the upper rack if there are not enough dishes for a full load. This will allow you to save on water and energy consumption. To select . load: 1. Select the programme and then press the . load button (Fig.2-19) – the . load indicator blinks. 2. Close the door. The programme starts automatically. To cancel the . load Follow the ‘Cancelling a programme in progress’ instructions. Note: Please keep in mind that the amount of detergent should also be adapted to the . load. 3-in-1 Function When using ‘3-in-1’ dishwasher tablets the rinse aid and salt functions are no longer useful. It may be advisable to switch the rinse aid off and select the lowest possible setting for water hardness. Press the ‘3-in-1’ button (Fig.2-20) to deselect the rinse aid function. If returning to a standard detergent system it is advisable to: 1. Refill both the salt and rinse aid compartments. 2. Switch the water hardness setting to the highest possible position and run for three normal cycles without a load. 3. Readjust the water hardness setting again for local water conditions. Memory Function Module If a power cut occurs while the selected washing program is active, the program is not cancelled. The controls use a microprocessor device to memorize the information about the selected washing program. Once the power is returned to the machine, the dishwasher will resume from the point it was interrupted. 10 3. Looking after your Dishwasher Care After Every Wash After every wash, set the ON-OFF button to OFF and leave the door slightly ajar so that moisture and odours are not trapped inside. Before cleaning or performing maintenance isolate . from mains. Overall condition of appliance Check that no grease or scale has accumulated on the inside of the dishwasher. If you discover any deposits: Clean the interior of the dishwasher thoroughly with a detergent solution. Dishwasher salt Check the LOW SALT indicator. Top up with salt, if required (Fig.3-1). Rinse-aid Check the LOW RINSE AID indicator (Fig.3-2), on the front panel. Top up with rinse-aid if required. Filters The filters prevent larger particles of food in the water from reaching the pump. These particles may occasionally block the filters. When the appliance has finished washing, check the filters for particles of food and, if required, clean. After undoing the coarse micro-filter (Fig.3-3), the filter unit can be removed (Fig.3-4). Remove any particles of food and rinse the filters under running water. Insert the filter unit and tighten the coarse micro-filter. Fig.3-1 Fig.3-2 Fig.3-3 Fig.3-4 11 Spray arms Limescale and remnants of food in the washing water can block the nozzles in the spray arms and the arm mountings. Inspect the nozzles in the spray arms for blocked holes due to remnants of food. If necessary, pull the lower arm (Fig.3-5) upwards and lift it off. Unscrew the upper spray arm (Fig.3-6). Clean both spray arms under running water. .Refit the spray arms. Ensure that the lower arm has locked into place and the upper one is screwed tight. position. If absolutely necessary, it can be positioned on its back. Seals One of the factors that cause odours to form in the dishwasher is food that remains trapped in the seals. Periodic cleaning with a damp sponge will prevent this from occurring. When You Go on Holiday When you go on holiday, it is recommended that you Fig.3-5 Fig.3-6 position. If absolutely necessary, it can be positioned on its back. Seals One of the factors that cause odours to form in the dishwasher is food that remains trapped in the seals. Periodic cleaning with a damp sponge will prevent this from occurring. When You Go on Holiday When you go on holiday, it is recommended that you Fig.3-5 Fig.3-6 run a wash cycle with the dishwasher empty and isolate from the mains. Turn off the water supply and leave the door of the appliance slightly ajar. This will help the seals last longer and prevent odours from forming within the appliance. 12 4. Troubleshooting Resolving minor problems yourself Experience has shown that you can resolve most problems that...