2. Unscrew filter cylinder as illustrated and take out filter system. en Fault, what to do? 3. Remove any residue and clean filters under running water. 4. Re-install filter system in reverse sequence and ensure that the arrow marks are opposite each other after closing the filter system. Spray arms Limescale and contaminants in the rinsing water may block nozzles and bearings on the spray arms 1: and 1J. 1. Check outlet nozzles on the spray arms for blockages. 2. Unscrew the upper spray arm 1:. 3. Remove the lower spray arm 1J upwards. 4. Clean spray arms under running water. 5. Re-engage or screw on spray arms. 3 Fault, what to do? Experience has shown that you can rectify most faults which occur in daily operation yourself. This ensures that the machine is quickly available to you again. In the following overview you can find possible causes of malfunctions and helpful information for rectifying them. Note If the appliance stops during dishwashing or does not start for no obvious reason, first run the Abort programme function (Reset). (See chapter entitled “Operating the appliance”) a Warning – Don’t forget: Repairs may be carried out by technicians only. If a component has to be replaced, ensure that only original spare parts are used. Improper repairs or use of non-original spare parts may cause considerable damage and put the user at considerable risk. Fault, what to do? en Error message in the display window Some faults are stated in the display window )2 and possible remedial actions are offered (e.g. Filter system soiled (E22) --> Clean filters) Waste water pump Large food remnants or foreign objects which were not captured by the filters may block the waste water pump. The rinsing water will then be above the filter. In this case: 1. First always disconnect the appliance from the power supply. 2. Take out top basket 12 and bottom basket 1b. 3. Remove the filters 1Z. 4. Scoop out water, use a sponge if required. 5. Prise out the white pump cover (as illustrated) using a spoon. Grip the cover on the crosspiece and lift diagonally inwards. Remove cover completely. 8.Install filters. 9.Re-insert baskets. 6. Check impeller wheel and remove any foreign objects. 7. Place cover in the original position and press down until it engages (click). en Fault, what to do? Fault table Fault Cause Remedial action “Check water supply” Supply hose kinked. Install supply hose without kinks. display @ lights up. Tap turned off. Turn on the tap. Tap jammed or calcified. Turn on the tap. Flow rate must be min. 10 l/min. when water supply is open. Filter in the water supply blocked. Switch off the appliance and pull out the mains plug. Turn off the tap. Unscrew water connection. Clean filter in the supply hose. Screw water connection on again. Check for leaks. Reconnect power supply. Switch on the appliance. Error code “:.. is lit. Error code “:.… is lit. Filters 1Z are soiled or blocked. Waste water hose is blocked or kinked. Clean filters. (See Cleaning and maintenance) Install hose without kinks, remove any residue. Siphon connection still sealed. Check connection to siphon and open if required. Error code “:.† is lit. Error code “:.. is lit. Cover on the waste water pump loose. Waste water pump blocked or cover on the waste water pump is not locked in position. Mains voltage too low. Lock cover correctly. (See Waste water pump) Clean pump and lock cover correctly. (See Waste water pump) Not an appliance fault, have the mains voltage and electrical installation checked. Fault, what to do? en Fault Cause Remedial action A different error code is indicated on the digital display. A technical fault has probably occurred. Switch off appliances with the ON/OFF switch (. After a short time restart the appliance. (“:‹‚ to “:„‹) If the problem recurs, turn off the tap and pull out the mains plug. Call customer service and mention the error code. Display flashes Door not closed properly. Close the door. Ensure that no objects (utensil, fragrance dispenser) are protruding over the basket and preventing the door from closing. Refill indicator for salt H and/or rinse-aid P is lit. No rinse aid. No salt. Refill rinse aid. Refill with special salt. Sensor does not detect salt tablets. Use different special salt. Refill indicator for salt H and/or rinse-aid P is not lit. Refill indicator switched off. There is still enough special salt/ rinse aid available. Activation/deactivation (see chapter Water softening system/Special salt or Rinse aid). Check refill indicator, levels. Water is left in the appliance at the end of the programme. Filter system or area under the filters 1Z is blocked. The programme has not yet ended. Clean filters and area underneath (see Waste water pump). Wait until programme ends or reset (see Terminating the programme). en Fault, what to do? Fault Cause Remedial action Utensils not dry. No or too little rinse aid in the dispenser. Programme selected without drying. Water collecting in depressions on the ute...

Ce manuel est également adapté pour les modèles :
Lave-vaisselle - S41T69N2GB/73 (2.09 mb)