Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
Press the “A” button until the display shows “r:02”. Press the “C” button to change the amount of Rinse Aid dispensed. "r:00" = Rinse Aid OFF "r:06" = highest setting Press START to save setting and close the door. 16 CARE AND MAINTENANCE CARE AND MAINTENANCE MAINTENANCE TASKS Certain areas of your dishwasher require occasional maintenance. The maintenance tasks are easy to do and will ensure continued superior performance from your dishwasher: Overall condition of the machine Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any resulting damage. Regularly wipe the front of the appliance and door seal with a damp cloth - water and a small amount of liquid soap is adequate. Do not use sponges as they could scratch the surfaces. Stainless steel appliances: To prevent corrosion, do not use sponges. Clean the outer edges of the inside door panel regularly to remove debris that may collect from normal loading. If spots begin to appear on the stainless steel, make sure the rinse agent is full and functioning properly. WARNING Use caution when removing parts for cleaning as some debris may be sharp. Filters The filter system consists of a coarse filter, a flat fine filter and a micro filter. The filters keep large foreign objects in the rinsing water away from the pump. Foreign objects may occasionally block the filters. Check the filters for residue by unscrewing the filter cylinder as illustrated and take out the filter system. Remove any residue and clean filters under running water. Reinstall filter system in reverse sequence and ensure that the arrow marks are facing each other after locking it into place. Spray Arms Check spray arms for grease and limescale deposits. If you find such deposits, fill detergent dispenser with detergent and start the appliance without utensils in the cycle with the highest rinsing temperature (see wash cycle information table). Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers. Unscrew the spray arms and inspect as shown. Waste water pump Large food remnants in the rinsing water not retained by the filters may block the waste water pump. In this case: Disconnect the appliance from the power supply. Remove the filters as previously shown. Scoop out standing water - use a sponge if necessary. Using a spoon, pry off the pump cover, then grip the cover and pull upward until it resists and then pull forward. .. Check inner compartment and remove any foreign objects. Place cover in the original position, press down and engage until it clicks. ............ Preparing your unit for vacation Before leaving for vacation during warmer weather, besides turning off the main valve, also turn off water supply at the nearest point to the dishwasher (usually under the kitchen sink). During colder weather, please follow the instructions for winterizing your unit below. Winterizing your unit If your dishwasher will be unused for an extended period of time in a location that experiences freezing temperatures (holiday home or through a vacation period), have your dishwasher winterized by an authorized professional service. .... 17 TROUBLESHOOTING TROUBLESHOOTING Dishwashers may occasionally exhibit problems that are unrelated to a malfunction of the dishwasher itself. The following information may help you with a dishwasher problem without involving a repair professional. The items listed in the following charts may not be covered by your product warranty. Problem Cause Action Dishwasher does not start 1. Door may not be properly latched. 2. Unit may not be turned on. 3. Unit not reset or previous cycle not completed. 4. Delay start engaged. 5. Interruption of electrical power supply to dishwasher or circuit breaker or blown fuse. 6. The door may have been closed without first selecting a cycle. 7. Water supply may not be turned on. 1. Shut the door completely. 2. Press the main power switch to turn unit on. 3. To reset, refer to “Canceling a cycle/Changing a cycle” section in this manual. 4. To reset, refer to “Delay Start” section in this manual. 5. Check circuit breaker or blown fuse. 6. Select a cycle and then close the door. 7. Check and turn on water supply. Dishwasher Default factory settings alert the customer that the To adjust the volume or deactivate, refer to “Cycle Completion Signal” beeping cycle has completed by beeping. This feature can be section in this manual. (end of cycle deactivated if so desired. signal) Display does not illuminate or console lights are not on 1. A fuse may have been blown or circuit breaker tripped. 2. Door not closed or latched. Note: For models with controls on the top portion ofthedoor,thedisplay only illuminates when the door is opened and controls are visible. 1. Check the fuse or circuit breaker box and replace the fuse or reset the breaker if necessary. 2. Ensure that door is properly latched and completely closed. Dishwasher seems to run a long time 1. ...
Ce manuel est également adapté pour les modèles :Lave-vaisselle - S46KML15UC/01 (3.23 mb)
Lave-vaisselle - S46KML16UC/01 (3.23 mb)