Log:
Évaluations - 0, GPA: 0 ( )

Instructions Bosch, Modèle S5447X1/40

Fabricant : Bosch
Taille : 2.31 mb
Nom Fichier :
Langue d'enseignement: en
Aller à la télécharger



Par ce dispositif a également d'autres instructions :

Facilité d'utilisation


Ensure that the drainage hose is not kinked, crushed or twisted (ensure that there is no sealing cover which prevents the waster water from flowing away!). Fresh water connection Using the enclosed parts, connect the fresh water connection to the tap according to the installation instructions. Ensure that the fresh water connection is not kinked, crushed or twisted. When replacing the appliance, always connect a new water supply hose to the water supply. The old supply hose must not be re-used. Ensure that the fresh water connection is not kinked, crushed or twisted. Water pressure: Minimum 0,5 bar – maximum 10 bar. If the water pressure is higher, install a pressure reducing valve. Flow rate: Minimum of 10 litres per minute. Water temperature: We recommend that you use cold water. If you do use hot water, the temperature should not exceed 60 °C. Electrical connection This appliance should only be connected to a 230/240 V AC source via a properly installed earthed socket. See nameplate 31 for size of required fuse. The socket must be installed close to the dishwasher. If the domestic wiring includes a residualcurrent- operated (FI) circuit-breaker, make sure that it bears the mark, as only this type conforms to the latest regulations en Disconnecting the dishwasher Here too, it is important that tasks are carried out in the correct sequence: always unplug the appliance from the mains electricity first of all. Pull plug out of wall socket. Turn off water supply. Disconnect drain and water input hoses. Remove screws in underside of work surface. Detach base board, if fitted. Pull out appliance and carefully withdraw hoses at same time. Transporting the dishwasher Drain water from the dishwasher. Secure all loose parts. The appliance should only be transported in an upright position. If the appliance is not kept upright during transport, any water left inside may seep into the control module and cause subsequent errors with programme functions. The appliance must be drained in the following sequence: Turn on the tap. Set main switch to ON. Select the B programme. The programme duration in minutes is shown in the numerical display. Close the door. Wait for approximately 4 minutes. Terminate the programme by pressing A and C simultaneously. The time display changes to . Wait a further minute and then switch the appliance off. Turn off the tap. Protection from freezing temperatures If the appliance is installed in a location where there is a risk of freezing temperatures (e.g. in a holiday home), all water must be completely drained out of the interior (see “Transporting the dishwasher”). Turn OFF the tap, disconnect the supply hose and allow to drain. en AQUA-Safe Warranty. (not applicable to appliances without Aqua-Safe) In addition to warranty claims against the seller based on the sales agreement and in addition to our appliance warranty we shall replace the appliance under the following conditions: 1. If damage is caused by water due to a malfunction of our Aqua-Safe system, we shall make good the damage in the case of private consumers. 2. This liability warranty is valid for the service life of the appliance. 3. The warranty claim is subject to correct installation and connection of the appliance in accordance with our instructions. “This also includes correct installation of the Aqua-Safe extension (original accessory).” Our warranty does not cover defective supply lines or fittings up to the Aqua-Safe connection on the tap. 4. In prin...

Ce manuel est également adapté pour les modèles :
Lave-vaisselle - S5447X1/42 (2.31 mb)
Lave-vaisselle - S5447X2/40 (2.31 mb)
Lave-vaisselle - S5447X2/45 (2.31 mb)
Lave-vaisselle - S5456X2GB/40 (2.31 mb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories