Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
The buzzer for a fault sounds four times without pausing. The buzzer is activated by default. It can be turned off, so it does not sound at the end of a program. The buzzer for a fault cannot be turned off. . Open the door. . Turn the dishwasher off with the . button. . Press and hold the Program button and turn the dishwasher on simultaneously using the . button. Keep the program button pressed for at least four seconds until the lower right program indicator lights up. If it does not come on, start over. . Press the Program button four times briefly. The "Intake/Drain indicator flashes 4 times at short intervals. The sequence of flashing by the upper right program indicator shows whether the program end buzzer is turned on or off: – upper right program indicator flashing: buzzer is turned on – upper right program indicator is off: buzzer is turned off . To change the setting press the "Program" button (for at least one second) until the "Intake/Drain" indicator lights up. . Now press the Program button briefly. The setting is saved immediately. . Turn the dishwasher off with the . button. Additional options Factory default All settings can be reset to factory default. . Open the door. . Turn the dishwasher off with the . button. . Press and hold the Program button and turn the dishwasher on simultaneously using the . button. Keep the Program button pressed for at least four seconds until the lower right program indicator lights up. If it does not come on, start over. . Press the Program button briefly 12 times. The "Intake/Drain" indicator flashes once long and twice short. The sequence of flashing by the upper right program indicator shows whether a setting has been set differently to the default setting. – upper right program indicator flashes: all values are set to the default settings. – upper right program indicator is off: at least one setting has been changed. . To reset the dishwasher to factory default press the "Program" button (for at least one second) until the "Intake/Drain" indicator lights up. . Now press the Program button briefly. The setting is saved immediately. . Turn the dishwasher off with the . button. Frequently Asked Questions Repairs should only be carried out by a qualified and trained person in accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage. Technical faults Problem Possible fault Solution The dishwasher does not start. The door is not properly closed. Push the door firmly shut. The machine is not plugged in. Insert the plug. The circuit breaker has tripped. Reset the circuit breaker (see the data plate for minimum amperage). The dishwasher is not turned on. Press the . button and select a program. The dishwasher The circuit breaker has – Reset the circuit breaker (see stops during a tripped. the data plate for minimum program. amperage). – If the circuit breaker trips again, contact Miele. The buzzer sounds. All indicator lights of the program selection flash when the door is open. There may be a technical fault. – Turn the dishwasher off with the . button. After a few seconds: – Turn the dishwasher on. – Select the desired program with the Program selection button. – Close the door. If the indicator lights flash again, a technical fault has occurred. – Contact Miele. The drain pump may also be running when the door is open. The waterproof system has activated. – Turn off the water supply. – Contact Miele. Frequently Asked Questions Faults in the water intake/water drain Problem Possible fault Solution The dishwasher stops shortly after the program starts. The buzzer sounds. The "Intake/Drain" indicator flashes and lights up alternately when the door is open. The water supply valve is closed. – Open the water supply valve all the way. The dishwasher has stopped. The buzzer sounds. The "Intake/Drain" indicator flashes when the door is open. Before fixing the fault: – Turn the dishwasher off with the . button. Fault in the water intake. – Open the water supply valve all the way. – Clean the water intake filter (see "Cleaning and Care"). – The water pressure at the water connection is less than 30 kPa (0.3 bar/4.35 psi). Consult a plumber. Fault in the water drain. – Clean the triple filter (see There might be water in "Cleaning and care"). the wash cabinet. – Clean the drain pump (see "Cleaning and Care"). – Clean the non-return valve (see "Cleaning and Care"). – Remove any kinks in the drain hose. Frequently Asked Questions General problems with the dishwasher Problem Possible fault Solution The display is dark and only the " . " indicator lights. The indicator lights go out automatically to save energy (Standby). Press any button (except ) to come out of Standby mode. Detergent residue is left in the dispenser at the end of a program. The dispenser was damp when detergent was added. Dry the dispenser before adding detergent. The detergent dispenser lid cannot be closed properly. Detergent residue is blo...