Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
Models DD602 DD602IPart No. 599065/D Table of Content. Sectio. . General Informatio. 1.. Preparatio. 1.. Product Specifications & Cavity Dimension. 1.. Options for Installing Multiple Product. 1.. Electrical, Plumbing & Drainage Informatio. 1.. Product Part. 1.. Additional Product Parts for Integrated DishDrawe. Sectio. . Foot Slide Retainer Informatio. 2.. Assembling the Foot Slide Retaine. 2.. Securing the Foot Slide Retaine. Sectio. . Fitting the DishDrawe. 3.. Connecting the Service. 3.. Flexible Extrusion Attachment for 24. by 341/2. (610mm x 876mm) Cavit. 3.. Adjusting the Fee. 3.. Fitting the Endplate to the Chassis (Optional. 3.. Securing the DishDrawe. Sectio. . Prefinished Toe Kick Installatio. 4.. Setting the Upper Toe Kick Heigh. 4.. Trimming the Lower Toe Kic. 4.. Trimming the Toe Kick Pin. 4.. Adjusting the Upper Toe Kic. Sectio. . Information for Cabinet Maker for Integrated DishDrawe. 5.. Integrated Drawer Front & Toe Kick Dimension. Sectio. . Integrated Drawer Front Installatio. 6.. Changing the Integrated Badge Enclosur. 6.. Disassembling the Integrated Badg. 6.. Assembling the Integrated Badg. 6.. Fitting the Badge, Handle & Mounting Panel to the Drawer Fron. 6.. Fitting the Drawer Front Panels to the DishDrawe. Sectio. . DishDrawer Toe Kick Informatio. 7.. Integrated Toe Kick Installatio. Sectio. . Final Check. 8.. Installation Wet Tes. 8.. Troubleshootin. Page DD_0. SECTION 1SECTION 1 GENERAL INFORMATIO. STEP 1.1PREPARATION NOTE TO THE INSTALLE. • Be sure to leave these instructions with the Customer. • Ensure this appliance is properly grounded. NOTE TO THE CONSUME. • Keep these Installation Instructions with your Use & Care Manual for futur. reference. IMPORTAN. • Read these Instructions completely and carefully. • Observe all governing Codes and Ordinances. WARNIN. • These Instructions are intended as a guide only. • It is the responsibility of the plumber and electrician to ensure that each installatio. complies with all Codes and Ordinances. • Installation of this DishDrawer requires basic mechanical and electrical skills. • The installer is responsible for the DishDrawer installation. Improper installation is not covered under the Express Warranty Form. IMPORTAN. • At the completion of the DishDrawer installation, the Installer must perform Fina. Checks as per Section 8 of these Installation Instructions. • Ensure the DishDrawer enclosure is prepared for installation. • Remove all packaging and materials supplied with the DishDrawer. • If you have any questions concerning the installation of this DishDrawer, contact. Fisher & Paykel Customer Care Centr. 27 Hubbl. TOLL FREE 1-888-9-FNP US. Irvin. TOLL FREE 1-888-9-36 7 87. CA 9261. Fax (949) 790 891. US. WWW.FISHERPAYKEL.CO. STEP 1.2PRODUCT SPECIFICATIONS & CAVITY DIMENSIONS Electrica. 110-120 VA. (Water pressure below 7 p.s.i. 3 pin socket outle. (50 kpa) may require the electronic. Dryin. Residual Hea. to be re-programmed by a Servic. & Fan Assiste. Person at the time of installation. Water Connectio. Recommended Ho. 140°F Max. (60°C. Water Pressur. Maximum 139 p.s.i. (960 kpa. Minimum 4.3 p.s.i. (30 kpa. WARNIN. Before installing th. DishDrawer, remove th. house fuse or open th. circuit breaker. Ensure all wate. connections are turne. WARNIN. The DishDrawer MUS. be installed to allow fo. future removal from th. enclosure if service i. required. Page DD_0. IMPORTAN. Where the DishDrawe. is installed under . counter top, it i. recommended that bar. wood surrounding th. DishDrawer is seale. with an oil based pain. or polyurethane t. prevent possible stea. damage. IMPORTAN. Ensure the cavity side. are plumb (vertical) a. this will assist wit. leveling the DishDrawer. IMPORTAN. Ensure the Services Hol. is as close as possible t. the rear lower corner o. the cabinetry. The hol. can be located on eithe. side depending on th. location of the services. IMPORTAN. On corner installations. ensure that there is a ga. of 2" (50mm) minimu. between the adjacen. cabinetry and sides o. drawers. STEP 1.. OPTIONS FOR INSTALLING MULTIPLE PRODUCT. STEP 1.. ELECTRICAL, PLUMBING & DRAINAGE INFORMATIO. ELECTRICA. Care should be exercised when the appliance is installed or removed, t. reduce the likelihood of damage to the power supply cord. If the power supply cord is damaged, it must be replaced by the Manufacturer, it.s Servic. Agent or a similarly qualified person, in order to avoid a hazard. The power supply receptacle for the appliance should be installed in a cabinet or on a wal. adjacent to the under counter space in which the appliance is to be installed. The power supply receptacle should be positioned between 6" and 18. (150mm and 450mm) from the cabinet opening of the DishDrawer. GROUNDING INSTRUCTION. This appliance must be grounded. In the event of malfunction o. breakdown. grounding will reduce the risk of electric shock by providing a path of leas. resistance for electric current. This appliance is equipped with a cord having an equipment...