Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
208-240/60/1 . 208-240/60/3 . 480/60/3 MODEL . AM15VLF OPTIONS AT EXTRA COST . Single point electrical connection (3 phase only) ACCESSORIES . Peg rack . Combination rack . Sheet pan rack . Flanged and seismic feet . End of cycle audible alarm (field activated) . Drain water tempering kit . Spray hose Specifications, Details and Dimensions on Inside and Back. VENTLESS VENTLESS FRONT LOADING DISHWASHER 701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART • Page 2 of 8 F-40273 – Ventless Front Loading Dishwasher VENTLESS FRONT LOADING DISHWASHER 701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART • F-40273 – Ventless Front Loading Dishwasher Page 3 of 8 RECOMMENDED CONDENSE TIMES (BASED ON INCOMING WATER TEMP.) INCOMING TEMP. (F°) CONDENSE TIME (SEC.) RINSE TIME (SEC.) RACKS PER HOUR (1 MIN. CYCLE) 60 30 10 30 65 33 11 27 70 36 12 26 75 39 13 24 80 42 14 23 85-90 45 15 22 Ventless Front Loading Dishwasher Machine Ratings (Mechanical) Racks per Hour (Max.) 30 Dishes per Hour (Average 25 per rack) 750 Glasses per Hour (Average 45 per rack) 1,350 Table to Table - Inside Tank at Table Connection (Inches) 251.4" Overall Dimensions - (H x W x D) (Inches) 80" x 293.4" x 30" Wash Motor H.P. 2 Wash Tank Capacity - Gallons 14 Wash Pump Capacity - Gallons per Minute - Weir Test 160 Electric Booster Heater (Kw) 8.5 Kw Electric Heating Unit (Regulated) 5 Kw Blower Motor H.P. 1/20 Rinse Pump Motor H.P. 1/15 Rinse - Minutes operated during hour of capacity operation 5.00 Seconds of rinse per rack 10 Rate of Rinse Flow - Gallons per Minute - at 20 lbs. Flow Pressure 4.4 Rinse Consumption - Gallons per Hour - Maximum - at 20 lbs. Flow Pressure 22.2 Rinse Cycle - Gallons per Rack - at 20 PSI Flow .74 - 180°F Min. Peak Rate of Drain Flow - Gallons per Minute (Initial rate with full tank) 14 Exhaust Requirements 0 Shipping Weight Crated - Approx. lbs. - Unit only 522 The microcomputer-based control system is built into the AM Select Ventless dishwasher. It is available in standard electrical specifications of 208-240/60/1, 208-240/60/3, 480/60/3 and is equipped with a reduced voltage pilot circuit transformer. Water hardness must be controlled to 3 grains of hardness or less for best results. CONSTRUCTION: Drawn tank, tank shelf and feet constructed of 16 gauge stainless steel. Wash chamber and front trim panel above motor compartment are polished, satin finish. Frame is 12 gauge stainless steel, chamber is 18 gauge, and removable trim panels are 20 gauge. CHAMBER: Stainless steel chamber with large 203.4" W x 27" H opening will accommodate 18" x 26" sheet pans or a 60-quart mixing bowl. CHAMBER LIFT: Chamber coupled by stainless steel handle, spring counterbalanced. Chamber guided for ease of operation and long life. WASH PUMP: With stainless steel pump and impeller, integral with motor assures alignment and quiet operation. Pump shaft seal with stainless steel parts and a carbon ceramic sealing interface. Easily removable impeller housing permits ease of inspection. Capacity 160 GPM. Pump is completely self-draining. WASH PUMP MOTOR: Built for Hobart, 2 H.P., with inherent thermal protection, grease-packed ball bearings, splash-proof design, ventilated. Single-phase is capacitor-start, induction-run type. Three-phase is squirrel-cage, induction type. RINSE PUMP: Powered by a 1.15 H.P. single phase motor, the rinse pump is made of high strength engineered composite material. BLOWER: The condenser blower is an all stainless steel forward curved centrifugal wheel powered by a 1.20 H.P. TEFC single phase motor for nearly silent operation. CONDENSER COIL: The condensing system using a tube and fin coil constructed of copper and corrosion resistant aluminum. MICROCOMPUTER CONTROL SYSTEM: Hobart microcomputer controls, assembled within water- resistant enclosure, provide built-in performance and reliability. The microcomputer control, relays and contactors are housed behind a stainless steel enclosure, hinged to provide easy access for servicing. The line voltage electrical components are completely wired with 105°C, 600V thermoplastic insulated wire with stranded conductors. Electrical components are wired with type ST cord. Line disconnect switch NOT furnished. CYCLE OPERATION: The microcomputer-timing program is started by closing the doors, which actuates the door cycle switch. The cycle light turns ON. The microcomputer energizes the wash pump motor contactor during the wash portion of the program. After the wash, a dwell permits the upper wash manifold to drain. At the end of the dwell, the final rinse...