Évaluations - 5, GPA: 4
(
)
)
|
Facilité d'utilisation
• 5: Pull down the knob of the cartridge until it clicks. 198 e Removing Jammed Staples • 6: Hold the green lever and reinstall the cartridge until it clicks. • 7: Close the front cover of the finisher. 199 Troubleshooting y Removing Punch Waste Note . While “Hole punch receptacle is full.” is displayed, you cannot use the Punch function. A Open the front cover of the 2 Tray finisher. BPull out the punch waste box and remove punch waste. C Reinstall the punch waste box. Note . If you do not, “Hole punch receptacle is full.” is still displayed. D Close the front cover of the 2 Tray finisher. “Hole Punch Receptacle Full.” disappears. Note . If the message is still displayed, reinstall the punch waste box. 200 5. User Tools (Copy/ Document Server Features) Accessing the User Tools (Copy/ Document Server Features) This section is for the key operators in charge of this machine. You can change or set the machine's default settings. Preparation After using the User Tools, be sure to exit from the User Tools. The selected key is highlighted. Any changes you make with the User Tools remain in effect even if the main power switch or operation switch is turned off, or the {Clear Modes} key is pressed. Reference For details, . “Accessing the User Tools (System Settings)” in the System Settings manual. A Press the { {{{{User Tools/Counter} }}}} key. The User Tools Main Menu appears. B Press the [Copier/Document Server Features] key. The Copier/Document Server Features menu appears. C Select the desired menu and press the key. Note . [T TTTTNext]: Press to go to the next page. . [U UUUUPrevious]: Press to go back to the previous page. Reference . P.204 “User Tools Menu (Copier/ Document Server Features)”. D Change the settings by following the instructions on the display panel. Then press the [OK] key. Reference . P.212 “General Features 4/4”. Note . [OK]: Press to set the new settings and return to the previous menu. . [Cancel]: Press to return to the previous menu without changing any data. User Tools (Copy/Document Server Features) Exiting From the User Tools A After changing the User Tools settings, press the [Exit] key on the User Tools Main Menu. Changing the User Tools is completed, and the machine is ready for copying. 5 Note . To exit from the change of the machine's default settings and return to Copy mode, press the {User Tools/Counter} key. . You can also exit from the User Tools by pressing the {User Tools/Counter} key. 202 Accessing the User Tools (Copy/Document Server Features) 203 User Tools (Copy/Document Server Features) User Tools Menu (Copier/Document Server Features) 5 204 User Tools Menu (Copier/Document Server Features) 2055 User Tools (Copy/Document Server Features) General Features 1/4 . ....Auto Paper Select Priority As a default setting, Auto Paper Select is selected. You can cancel this setting. Note . Default: Yes . ....Auto Tray Switching If you load paper of the same size in two or more trays, the machine automatically shifts to another tray when the tray in use runs out of paper (when Auto Paper Select is selected.) This function is called “Auto Tray Switching”. This setting specifies whether to use “Auto Tray Switching” or not. Default: With image rotation Note . [With image rotation] Use this when copying with Auto Tray Switching. . [Without image rotation] Only copies with Auto Tray Switching if you load paper of the same size and in the same direction in two or more trays. If the paper is not the same size or in the same direction, the message “Load paper.” is displayed. . [OFF] When a paper tray runs out of paper, copying is interrupted and the message “Load paper.” is displayed. . ....Paper Display You can choose whether the available paper trays/sizes are shown on the initial display at Auto Paper Select mode. Note . Default: Display . If you choose “Hide”, the display is shown as below. When the [Auto Paper Select] key is pressed, paper sizes appear on the display. . ....Original Mode Priority As a default setting, Text is selected as the Originals Type. You can change it to Text/Photo, Photo, Pale, or Generation Copy. Note . Default: Text 206 General Features 1/4 . ....Original Mode Display You can choose whether the original modes are shown on the initial display. Note . Default: Display . If you choose “Hide”, the display is shown as below. . ....Auto Image Density Priority You can turn the Auto Image Density on or off for each of the original types (Text, Text/Photo, Photo, Pale, and Generation Copy). Note . Default: Text: On, Text/Photo: On, Photo: Off, Pale: On, Generation Copy: On . ....Copy Quality You can adjust the quality level of copies for each of the original types (Text, Text/Photo, Photo, Pale, Generation Copy). • Text Adjust the sharpness of text. Note . Default: Normal . [Custom Setting] is the value set during service setup. . Choosing [Sharp] or [Sort] affects the outline sharpness of text. 207 User Tools (Copy/Document Server Features) • Text/Photo When there ...
Ce manuel est également adapté pour les modèles :Imprimantes - AFICIO 1045 (7.49 mb)