Évaluations - , GPA:
(
)
)
Fabricant : Citizen
Taille : 22.42 mb
Nom Fichier : e4f3bda8-9de1-4d49-b46d-c30c5e6c24dc.pdf
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Facilité d'utilisation
It cannot be positioned vertically or on a wall. Horizontal position Vertical position CAUTION Do not use the printer under the following conditions. • Locations subject to vibration or instability. • Locations that are very dirty or dusty. • Locations where the printer is not level. • The printer may fall and cause an injury. • The quality of printing may deteriorate. • Oriented other than as specified. • The printer may malfunction, be damaged, or cause an electric shock. —23— 3.6 Partition for Paper Roll 3.6 Partition for Paper Roll Set the partition to the width of the paper roll you are loading. The partition is set at the factory to the position shown below. • For 3-inch type: 80-mm wide paper roll • For 2-inch type: 58-mm wide paper roll 1. Turn off the power. 2. Press up on the cover open button to open the paper cover. 3. Press in the position shown by the arrow and set the partition in a slot that matches the width of the paper roll you are using. However, to use an 83-mm wide paper roll, remove the partition. 4. Refer to “5.3 Manual Setting of Memory Switches” to change the paper width settings. Partition *1 *1 *2 Notes: *1: 2-inch type (58/60 mm) *2: 3-inch type (80/83 mm) CAUTION Make sure the partition is not slanted when setting it for 58-mm or 60-mm paper rolls. —24— 3.7 Setting the DIP Switch on the Serial Interface Board 3.7 Setting the DIP Switch on the Serial Interface Board 1. Turn off the printer and unplug the power cord from the electric outlet. 2. Remove the mounting screws of the serial interface board. 3. Remove the serial interface board from the printer. 4. Set the DIP switch according to the following table. DIP switch Serial interface board mounting screws CAUTION When setting the DIP switch, do not remove any screws except the serial interface board mounting screws. The function of each switch is shown below. (Shaded values are factory settings. However, factory settings differ depending on the destination market.) Switch no. Function ON OFF 1 Communication condition setting According to DIP switch settings According to memory switch settings 2 Hand shake XON/XOFF DTR/DSR 3 Bit length 7 bits 8 bits 4 Parity check Yes No 5 Parity selection Even parity Odd parity 6 Baud rate selection Refer to table below. 7 8 INIT Reset Invalid Baud rate selection Baud rate (bps) Switch no. 6 7 2400 OFF OFF 4800 ON OFF 9600 OFF ON 19200 ON ON When switch no. 1 is set to OFF, you can use a command or a memory switch to select 1200, 38400, 57600, or 115200 bps. —25— 3.8 Adjusting the Paper Near-end Sensor 3.8 Adjusting the Paper Near-end Sensor Change the settings of the paper near-end sensor to set the position at which the near-end of the paper is detected. 1. Use a pointed object, such as a pen, to gently press the button to change the paper near-end sensor. 2. Press and hold down the button while moving the paper near-end sensor up, down, right and left. The sensor positions are shown below for the various diameters of the paper roll used. (Unit: mm) Sensor position Diameter when detected as near end Outer diameter of core of paper roll used A .31 .18 B* .23 .18 C Paper near-end sensor function is off Note: *: Position of sensor when shipped from factory. However, factory settings differ depending on the destination market. CAUTION • The amount of paper remaining on the roll (diameter of the roll) depends on the type of paper used. • The paper roll diameters in the table are guidelines. Button to change paper near-end sensor —26— 3.9 Setting Paper Thickness 3.9 Setting Paper Thickness Set the paper thickness selection lever (blue) to the thickness of the paper. 1. Turn off the power. 2. Press up on the cover open button to open the paper cover. 3. Lightly press the damper inward and check the position of the paper thickness selection lever. 4. Set the paper thickness selection lever to 1 for regular paper or 2 for thick paper. Gently press on the side of the lever with a pointed object, such as a pen, to move the paper thickness selection lever. Damper Paper thickness selection lever (blue) (Behind the damper) 1: Regular paper 65 .m - 85 .m 2: Thick paper 85 .m - 150 .m The paper thicknesses shown above are guidelines. Adjust the position of the lever to get the best printout. —27— — 28 — 1. Turn on the power. 2. Press up on the cover open button to open the paper cover. 3. Load the paper roll so that the printable side of the paper is facing up, as shown by arrow A. 4. Pull a few cm of paper straight out in the direction of arrow B. 5. Close the paper cover until you hear a click. Paper is fed and cut automatically (by the factory setting). 3.10 Loading Paper Refer to 5.3 Manual Setting of Memory Switches CAUTION .. Always use the specified types of paper rolls. .. Confirm that the paper roll is set correctly. .. If the paper is skewed and not coming straight out of the paper cover, open it and straighten the paper. .. Always pull a few cm of paper straight out of the printer if you open th...