Évaluations - 4, GPA: 3.5
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
NOTE: Do not turn the transfer belt over. If you do this, the toner may spill. 13Slide the transfer belt down into the printer and press it firmly into place. 6.20 MAINTAINING YOUR PRINTER 14Firmly push the lock levers on each side towards the top cover, as shown below, to lock the transfer belt into place. 15After making sure that the left cover is open, close the top cover. Make sure that it is securely latched. CAUTION: Do not try to close the left cover with the top cover open. This may cause damage to the printer. 16 Close the left cover firmly. 17Turn the printer on. 18In ready mode press the Menu button ( ) on the control panel until you see ’Setup’ on the bottom line of the display. 19Press the Enter button ( ) to access the menu. 20Press the scroll button ( or ) until ‘Maintenance’ displays on the bottom line and press the Enter button ( ). 21Press the scroll button ( or ) until ‘Check Others’ displays on the bottom line and press the Enter button ( ). 22Press the scroll button ( or ) until ‘Imaging Unit’ displays on the bottom line and press the Enter button ( ). 23Press the scroll button ( or ) to display ‘Reset’ and press the Enter button ( ). 6 24‘Reset Now’ appears on the bottom line of the display and Imaging Unit’ continuously appears on the display. the printer returns to the ready mode. NOTE: After replacing the imaging unit, you must reset the image counter for the imaging unit. If you do not do this, ‘Replace MAINTAINING YOUR PRINTER 6.21 Replacing the Transfer Belt The life of the transfer belt is approximately 50,000 black pages and 12,500 color pages. Replace the transfer belt when the control panel displays ‘Replace Transfer Belt’. To replace the transfer belt: 1 Turn the printer off, then wait a few minutes for the printer to cool. 2 Using the handle, completely open the left cover until it is at right angles to the main frame and the toner cartridges are ejected. CAUTION: If the left cover is not completely open, the top cover release button does not be pressed. 6.22 MAINTAINING YOUR PRINTER MAINTAINING YOUR PRINTER 6.23 6 3 Press the top cover release button to unlatch the top cover and open it all the way. 4 Pull the lock levers on each side towards you, as shown below, to release the transfer belt. 6.24 MAINTAINING YOUR PRINTER 5 Using the handle, lift the used transfer belt out of the printer by lightly pulling it towards the left of the printer. NOTE: Keep the transfer belt level and do not turn the transfer belt over otherwise loose toner may be spilled. 6 Take a new transfer belt out of the package. 7 Remove the paper covering on the transfer belt by removing the tape. CAUTION: Don’t use sharp objects, such as a knife or scissors, to open the transfer belt package. You could damage the surface of the transfer belt. MAINTAINING YOUR PRINTER 6.25 6 8 Pinch the transfer belt tention levers on both sides of the transfer belt. Then, pull them out, as shown below. 9 Locate the transfer belt slots inside the printer, one on each side. CAUTION: To prevent damage, do not expose the imaging unit to light for more than a few minutes. Close the top and left cover should the setup need to be halted for any reason. 6.26 MAINTAINING YOUR PRINTER 10Hold the handle on the new transfer belt and then align it with the slots inside your printer, on each side. NOTE: Keep the transfer belt level and do not turn the transfer belt over otherwise loose toner may be spilled. 11Slide the new transfer belt down into the printer and press it firmly into place. MAINTAINING YOUR PRINTER 6.27 6 12Firmly push the lock levers on each side towards the top cover, as shown below, to lock the transfer belt into place. 13After making sure that the left cover is open, close the top cover. Make sure that it is securely latched. CAUTION: Do not try to close the left cover with the top cover open. This may cause damage to the printer. 14Close the left cover firmly. 15Turn the printer on. 16In ready mode press the Menu button ( ) on the control panel until you see ’Setup’ on the bottom line of the display. 17Press the Enter button ( ) to access the menu. 18Press the scroll button ( or ) until ‘Maintenance’ displays on the bottom line and press the Enter button ( ). 19Press the scroll button ( or ) until ‘Check Others’ displays on the bottom line and press the Enter button ( ). 20Press the scroll button ( or ) to display ‘Transfer Belt’ on the bottom line and press the Enter button ( ). 21Press the scroll button ( or ) to display ‘Reset’ and press the Enter button ( ). 22‘Reset Now’ appears on the bottom line of the display and the printer returns to the ready mode. NOTE: After replacing the transfer belt, you must reset the image counter for the transfer belt. If you do not do this, ‘Replace Transfer Belt’ continuously appears on the display. 6.28 MAINTAINING YOUR PRINTER Cleaning the Printer During the printing process, particles of paper, toner and dust can accumulate inside the printer. Over time, this build-up can...
Ce manuel est également adapté pour les modèles :Imprimantes - CLP-550 (10.09 mb)
Imprimantes - CLP-550N (10.09 mb)