1 Press the tray open button. 2 Pull the tray open. 3 Remove the jammed paper by gently pulling it straight out as shown below. 9.1 9.2 4 Align the tray with the slot, and slide it into the machine. 5 Press the top cover lever, completely open the top cover. 6 Hold the top cover and close it slowly and carefully, until the cover is securely latched. Note If the top cover is not completely closed, the machine will not operate. Caution Be careful not to pinch your fingers, since the top cover is very heavy. 7 If the paper jam LED blinks, go to next step. 8 Open the rear cover. 9 Carefully take the jammed paper out of the machine. Caution Do not touch the fuser inside the machine. It is hot and could cause burns! The fuser's operating temperature is very hot. Take care when removing paper from the machine. 9.3 10 Hold both edges of the rear cover, and align it as shown in the following figure. Press the rear cover firmly until it clicks. Note If the rear cover is not completely closed, the paper jam may occur. 11 Open and close the top cover firmly. The machine will resume printing. Rear and inside the machine If paper is jammed in the rear and inside the machine, follow the next steps to release the jammed paper. 1 Open the rear cover. 2 Carefully take the jammed paper out of the machine. Caution Do not touch the fuser inside the machine. It is hot and could cause burns! The fuser's operating temperature is very hot. Take care when removing paper from the machine. 3 Hold both edges of the rear cover, and align it as shown in the following figure. Press the rear cover firmly until it clicks. Note If the rear cover is not completely closed, the paper jam may occur. 9.4 4 Press the top cover lever, completely open the top cover. 5 Hold the top cover and close it slowly and carefully, until the cover is securely latched. Note If the top cover is not completely closed, the machine will not operate. Caution Be careful not to pinch your fingers, since the top cover is very heavy. 6 If the paper jam LED blinks, go to next step. 7 Press the top cover lever, completely open the top cover. 8 Grasp the handles on the toner cartridge and pull to remove the cartridge out of the machine. Caution • Do not touch the green surface, the OPC drum or the front of the toner cartridge, with your hands or any other material. Use the handle on each cartridge in order to avoid touching this area. • If you leave the top cover open for more than a few minutes, the OPC drum can be exposed to light. This will cause damage to the OPC drum. Close the top cover should the installation need to be halted for any reason. Note If toner gets on your clothing, wipe it off with a dry cloth and wash it in cold water. Hot water sets toner into fabric. 9 Carefully take the jammed paper out of the machine. Caution Do not touch the fuser inside the machine. It is hot and could cause burns! The fuser's operating temperature is very hot. Take care when removing paper from the machine. 10 After removing the jammed paper, check for paper which may be In the exit area jammed in other parts of the machine. If paper is jammed in the paper exit area, follow the next steps to release 11 Slide the toner cartridge back into the machine. the jammed paper. 1 Press the top cover lever, completely open the top cover. 12 Close the top cover firmly. The machine will resume printing. 2 If a long portion of the paper is visible, pull it straight out. If there is any resistance removing the paper, stop pulling and go to step 4. Caution Do not touch the fuser inside the machine. It is hot and could cause burns! The fuser's operating temperature is very hot. Take care when removing paper from the machine. 9.5 3 Hold the top cover and close it slowly and carefully, until the cover is 4 Open the inner cover. securely latched. 1 inner cover Note If the top cover is not completely closed, the machine will not operate. Caution Do not touch the fuser inside the machine. It is hot and could Caution cause burns! The fuser's operating temperature is very hot. Be careful not to pinch your fingers, since the top cover is very Take care when removing paper from the machine. heavy. 5 Carefully take the jammed paper out of the machine. 6Close the inner cover. 7After removing the jammed paper, check for paper which may be jammed in other parts of the machine. 8Close the top cover firmly. The machine will resume printing. 9.6 Status display Explanation Solution OPEN The covers is not completely closed. Press the covers until it clicks. LED blinks There is a problem in the machine. Unplug the power cord and plug it back in. If the problem persists, contact the service representatives. LED blinks There is no paper in the tray. Load paper in the tray. (Page 4.5) LED blinks In the paper feed area and rear the machine. Clear the jam. (Page 9.1) Rear and Inside the machine. Clear the jam. (...
