Évaluations - 2, GPA: 3.5
(
)
)
|
Facilité d'utilisation
The combined number of channels required by all the fixtures on a serial data link determines the numof fixtures the data link can support. standard no more than 32 devices should be connected on one data link. Connecting more than 32 fixtures on one serial data link without the use of a DMX optically-isolated splitter may result in deterioration of the digital DMX signal. Maximum recommended number of fixtures on a serial data link: 32 fixtur To link fixtures together cables directly from a dealer/distributor or construct your own cable. If you choose to create your owcable please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic interference. Use a Beld Standard microphone cables cannot transmit DMX data reliably over long distances. The cable will have the following characteristics: Maximum capacitance between condu Maximum capacitance between conductor and shield – Maximum resistance of 20 ohms / 1000 ft. Nominal impedance: 100 – 140 ohms Text Box: Disconnect the power cord before replacing a fuse and always replace with the same type fuse. Disconnect the power cord before replacing a fuse and always replace with the same type fuse. Text Box: The fuse is located inside this compartment. Remove using a flat Rounded Rectangular Callout: The fuse is located inside this compartment. Remove using a flat head screwdriver. CABLE CONNECTORS CAUTION Do not allow contact between the common and the fixture’s chassis ground. Grounding the common verify correct polarity and to make sure the pins are not grounded or shorted to the shield or each otheRSION CHART Note! If you use a controller with a 5CHAUVET Model No: DMX5M The chart below details a proper cable conversion: ONVERSION CHART Contor Pin 1 Data ( - ) sign Pin 2 Pin 2 Data ( + ) signal Pin 3 Pin 3 Do not use Do not Do not use Do not niversal DM Rounded Rectangular Callout: Resistance 120 ohm 1/4w between pin 2 (DMX -) and pin 3 (DMX +) of the last fixture. COMMONDMX+ DMX- INPUT OUTPUT1 3 2 132132Resistance 120 ohm 1/4w between pin 2 (DMX -) and pin 3 (DMX +) of the last fixture. Termination reduces signal errors and to avoid signal transmission problems and interference, it is always advisable to connect a DMX signal terminator. DMX connector configuration 1. Connect the (male) 3 pin connector sidthe DMX cable to the output (female) 3 connector of the controller. Connect the end of the cable coming from the controller which will have pin connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then, proceed to connect from the outpuas stated ab fixture and so on. CHAUVET Certified DMX Data Cables Order Code D DMX1.5 DMX Cable 1.5m/4.9ft DMX4.5 DMX Cable 4DMX10 DMX Cable 10m/32.8ft Text Box: This drawing provides a general illustration of the DMX Input/Output panel of a lighting fixture. This drawing provides a general illustration of the DMX Input/Output panel of a lighting fixture. Master/Sl connector to the input connector oproceed to connect from the Often, the setup for Master-Slave d Standalone operation re initialized for this purpose via either ttings in the control panel or DIP- itches. Secondarily, the fixtures at follow may also require a slave M Rounded Rectangle: Often, the setup for Master-Slave and Standalone operation requires that the first fixture in the chain be initialized for this purpose via either settings in the control panel or DIP-switches. Secondarily, the fixtures that follow may also require a slave setting. Please consult the “Operating Instructions” section in this manual for complete instructions for this type of setup and configuration. O fixtu the fixture by loosening both knobs and tilting the fixture. After finding the desired position, retighten both knobs. • replacement access and routine maintenance. Safety cables should always be used. Never mount in places where the fixture will be exposed to rain, hihumidity, extreme temperature changes or restricted ventilationUse only heavy duty clamps for this fixture. 4. OPERATING INSTRUCTIONS Navigating the Control Panel Access control panel functions using the three panel buttons located directly underneath the LCD Display. Button Function