Évaluations - 4, GPA: 4.3
(
)
)
|
Facilité d'utilisation
1. Before running the self test, make sure there is sufficient paper to run the test (18" [46 cm]); the paper cover is closed; and that the printer is switched OFF. 2. Press and hold down the FEED pushbutton; then switch ON the printer to begin the test. Note: The test can be aborted by switching OFF the printer. 3. The following typical information is printed, followed by the printer’scomplete character set: Version : 1.1.6 Data bit : 8 bit Parity : None Baud rate : 9600 bps Handshaking : DTR Country : U.S.A. Print mode : Text (upright) Paper : Normal paper Density : 100% IrDA : IrDA-SIR Buffer size : 7000Byte Head volt : 7.1V Head temp. : 31°C Instruction 24-9422 Operation IrDA Printer Operation IrDA Printer The printer has been set up at the factory with the following default parameters: Baud rate : 9600 bps Handshaking : DTR Country : U.S.A. Print mode : Text (upright) Paper : Normal paper IrDA : IrDA-SIR If necessary, the default parameters can be changed as follows: 1. With the printer initially switched OFF, press and hold down the SELpushbutton; then switch the printer ON. 2. The printer now goes into its set-up mode and prints its current parameter status. Observe that the green Power LED flashes to indicate that the printer is in its set-up mode. Note: If no pushbuttons are pressed within 15 seconds, the set-up mode is automatically terminated without changing the original parameters. 3. Baud rate is first parameter printed. Pressing the FEED buttoncauses the value of that parameter to change in the sequence shownin the following table. SEL Button Baud rate HandshakingCountry Print mode PaperDensityIrDA FEED Button 2400, 4800, 9600, 19200, 38400, 57600, 115200 DTR, X-on/X-off U.S.A., Korea, Cyrillic, Denmark2, Norway, Japanese, Spain, Italy, Sweden, Denmark1, U.K., Germany, FranceText(upright), Data(inverted) Normal paper, Reprint paper50 – 150% in 5% stepsChamjin-Ir, IrDA-Sir, BHT-Ir(DENSO), EL-ME-Ir Instruction 24-9422 IrDA Printer Operation IrDA Printer Operation Press the SEL button to print the next parameter; then, if necessary, use the FEED button to change that parameter to the desired value. 5. Once all parameters have been set, press and hold down the SEL button then press the FEED button. Using the Printer Turn ON the printer and, if necessary, set it up as previously describedunder the heading Set-Up Mode. Also ensure that the instrument that is sending data to the printer is set up to operate in its IrDA print mode(refer to the instrument’s instruction manual for set up information). Align the printer’s infrared sensor to that of the instrument and beginprinting as described in the instrument’s instruction manual. Instruction 24-9422 Maintenance IrDA Printer Maintenance IrDA Printer WARNING! Remove all electrical connections before perform ing any maintenance work. Cleaning the Printer External surfaces of the printer may be kept clean by simply wiping witha damp cloth. Do not use any solvents that may attack the plastic case. Besure that the inside surfaces are kept dry at all times, and that theexternal surfaces are thoroughly dry before re-making any electricalconnections. Opening / Closing the Paper Cover From underneath the printer, use your thumb and forefinger to push upon the paper cover until it releases from its latches (see Figure 2.) Close the cover by pushing down until it snaps into place. Cleaning the Print Head To maintain a good print quality, it is recommended that the print headbe cleaned at least once a year or up to once a month if the printer is usedheavily. The print head should be cleaned immediately, however, if theprint becomes visibly fainter due to contamination of the print head. Clean the print head as follows: Material Required: • Isopropyl Alcohol • Cotton swabs Procedure: 1. Switch OFF printer. CAUTION: Allow the print head to cool before cleaning, otherwise damage to the print head may occur. 2. Open paper cover and remove paper roll. Instruction 24-9422 IrDA Printer Maintenance IrDA Printer Maintenance Using a cotton swab dampened with alcohol, wipe the heating dots ofthe print head. Be careful not to touch the heating dots with your fingers. 4. Allow the alcohol to dry. 5. Reload the paper and close the paper cover. Installing the Paper Replace the paper when it runs out as indicated by the front panel greenPower LED flashing. 1. Open the paper cover as previously described. 2. Remove the spent paper core. 3. Drop in a new paper roll so that it will rotate in the direction shownin Figure 2. 4. Insert edge of paper roll into slot in cover next to cutter; then close cover. Remove any slack by pulling out about . inch of paper from the printer. Note: If there was unprinted data in memory when the paper ran out, and the printer was not shut OFF, then the printer will automatically go on-line and print the remaining data 5 seconds after closing the paper cover. Figure 2. Installing the Paper Instruction 24-9422 Parts & Service IrDA Printer Parts & Servic...