Log:
Évaluations - 3, GPA: 3.3 ( )

Instructions Kenmore, Modèle 72785

Fabricant : Kenmore
Taille : 997.04 kb
Nom Fichier : 1007256L.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


Make sure you have all YOU MAY NEED: necessary disposer parts before install- Phillips Screwdriver, Drain Auger, 3/8" Electrical Clamp ing the disposer (see part identification Connector, Wire Nuts (2), Second 1 1/2" Drain Trap, diagram below). Hammer, Hacksaw, Water Hose Clamp, Pipe Wrench, Copper Ground Wire, Dishwasher Drain Connection Kit, Air Gap, Electrical On/Off Switch, Drain Tube Extension (_)1& 1 d #1 00 Otc N OR K #2 Mounting Assembly Disposer Discharge Assembly #1 A Stopper H Mounting Gasket/Splash Baffle M Nut B Sink Flange I Lower Mounting Ring N. Beveled DLscharge Tube C F_ber Gasket J D_shwasher Inlet #1 (1-1/2" Dlam ) D. Backup Rmg K D_scharge Outlet O. Beveled Washer E. Mounting Ring L' Wrenchette P. Flanged Gasket F Screws (3) OR G Snap Ring --Discharge Assembly #2 M. Bolt N. Discharge Tube (1-1/2" Diarn ) #2 O Flange P Gasket SAFETY SYMBOLS Danger indicates an I'_kWARNING I Warning indicates [',_gCAUTIONI Caution indicates a imminently hazardous situation which, a potentrally hazardous s_tuation potentially hazardous situation which, if not avoided, senous injury wdl result m death or which, if not avoided, could result death or serious injury m if not avoided, may result m minor moderate mjury or 72785 CHECK INSTALLATION DIMENSIONS 1odel A BC bE A. Disposer Height 010/6012 113/8" 6" 4" 65/16" 5" bowl to centerline of discharge ] B 01116013 12 5/8" 6" 4" 6 5/16" 5" B. Distance from bottom of sink outlet. (Add 1/2" when stainless steel sink is used.) A, 0552 12 5/8" 6" 4" 7 1/4" 5" C: Distance from centerline of the discharge outlet to end 5/8'--6,' 4,' 71/4,' 5" L of discharge tube. _3/4" 611/16" _ 53/4'_ 4'=._81/2'.=_=___' D: D_sposer Width D ---'----- E: Distance from disposer vertical 3/4" 6 11/16" 4" 8 1/2" 5 3/4" centerline to centerline of 0559* _1157/8" 9 7/16" 4" 7 1/2" 5 3/4" P-trap connection. --" 6" 4"71/4" 5" F: Centerline of disposer discharge to centerline at waste pipe entering wall. (Dimension "F" must be greater than 1/4" to prevent standing water in disposer.) 6" 4" 7 1/4" 5" If replacing an existing disposer, skip ahead to Instruction 6. ] _'" Indicates Batch Feed Model If this is a first time installation, continue with Instruction 2. / DISCONNECT SINK DRAIN 1. Loosen nut (A) at top of "P-trap" with pipe wrench (see Figure 2-1). 2. Loosen nut (B) at top of extension pipe. Remove extension pipe. J 3. Loosen nut (C) at base of sink flange. (If nut is corroded or too tight, apply penetrating lubricant 4. Push s_nk flange up through sink hole and remove it (see Figure 2-2). 5. Clean sink flange area of any putty or other debris. "- r " /_ DISASSEMBLE NEW DISPOSER MOUNTING ASSEMBLY 2-1 2-2 1. Insert wrenchette (or screwdriver) into one mounting lug and hold lower mounting ring securely with one hand (see Figure 3-1). With your other hand, turn mounting assembly counterclockwise to remove mounting assembly from lower mounting ring 2. Turn mounting assembly over (see Figure 3-2) and loosen three mounting / !i screws (A) until you can access snap ring (B). 3 Use screwdriver to pry snap ring off of sink flange. Mounting assembly will now come apart. INSTALL FLANGE IN SINK HOLE 3-1 3-2 1. Roll 1/4 pound (4 oz.) of non-hardening plumber's putty to make 3/4" thick rope to seal around sink flange. 2. Apply putty evenly around sink hole (see Figure 4-1). 3. Press sink flange slowly but firmly into sink drain hole to seat evenly on putty (see Figure 4-2). Use screwdriver or putty knife to scrape all putty from edge of sink hole. _k CAUTION Do not use plumber's putty on any other disposer connection -it 4-1 4-2 may harm disposer and cause property damage. ATTACH UPPER MOUNTING ASSEMBLYTO SINK FLANGE Sink Flange You may wish to place a we=ghted object in the sink to hold the sink flange in place. (Place a towel under object in sink to prevent scratching ) Reference F=gure 5-1 for part identification. Fiber Gasket / 1 Working from under sink, slip fiber gasket and 4 Tighten three mounting screws up to sink metal backup ring over sink flange. until mounting assembly is seated tightly Backup R=ng __ _._'_). 2 Holding fiber gasket and backup ring in place, and evenly against sink. shp mounhng nng over s_nkflange so it seats * Placing a thick, wide rubber band around against backup nng the sink flange (above the snap ring MountEng RLng __ X_-@ 3 W_th fiber gasket, backup nng, and mounting groove) may help hold parts Jnplace _,,hde ring hght to S,F.'.__ottom, shde snap r',ng cnto tnstalhng snap ring. (Remember to rer'nove s_nk flange until _tpops {nto groove on flange'. rubber band after snap ring is installed.) ' Snap Ring O If you are replacing an existing disposer, go to Instruction 6 If this is a first time _nstallahon, 1 skip ahead Io Instruction 7 J 5-1 REMOVE EXISTING DISPOSER 1. Turn off electrical power at fuse box or circuit breaker. Electric Shock o Turn off electrical power at fuse ,, Disposer must be grounded. box or circuit breaker before Improper connection can removing elect...


Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories