Évaluations - , GPA:
(
)
)
Fabricant : KitchenAid
Taille : 338.59 kb
Nom Fichier : 936f1a93-b683-4119-bac2-32a2572911d5.pdf
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Facilité d'utilisation
Homeowner: Keep Installation Instructions for future reference. Save Installation Instructions for local electrical inspector’s use. Before you start... Proper installation is your responsibility. Make sure you .... 1 Ij-min. ,... :j:.:. .-..x... 1 /*” have everything necessary for (38.4 cm) I correct installation. It is the ,:.:.: . ... ...:.:..... personal responsibility and I obligation of the customer to 24-3j4” contact a qualified installer to min. assure that electrical installation meets national and all local codes and ,:::: ordinances. 18”i min. Grounded electrical outlet is ( 45.7 cm) required. (“See Electrical requirements”.) Check the location where your I compactor will be installed. The cabinet opening should be square. You should be able to fully open the compactor drawer. Six inches (15.2 cm) of clearance is needed on the right side of compactor drawer to be able to remove compactor bag. Allow 23 inches (58.4 cm) in front of the 6” (15.2 cm) 33-15/i6” clearance right compactor to remove drawer. (86.2 cm) side of drawer for bag removal Fire Hazard 2;” (58.4 cm) clearance is Do not let any item fall or needed to fully open or collect behind the compactor. remove compactor drawer (61 cm) To do so may result in a fire. ,::: ..:: - Part No. 9870295 Tools and materials needed for instaIIatSon: Parts supplied for undercounter instaIIat3on: 1 LH retaining bracket 1 RH retaining bracket 2 retaining bracket screws #8 x 5/16 2 mounting clips 2 mounting screws #8 -18 x 112 All parts are in literature package in drawer, Electrical reauirements Impo~?an+: Observe all governing codes and ordinances. Electrical Shock Hazard l Electrical ground is required on this appliance. l If cold water pipe is interrupted by plastic, non- metallic gaskets or other insulating materials, Do Not use for grounding. l Do Not ground to a gas pipe. l Do Not modify the power supply cord plug. If it does not fit the outlet, have a proper outlet installed by a qualified electrician. l Do Not have a fuse in the neutral or grounding circuit. A fuse in the neutral or grounding circuit could result in an electrical shock. l Do Not use an extension cord with this appliance. l Check with a qualified electrician if you are in doubt as to whether the appliance is properly grounded. Failure to follow these instructions could result in serious injury or death. If codes permit and a separate grounding wire is used, it is recommended that a qualified electrician determine that the grounding path is adequate. A 120-volt, 60-Hz, AC-only, 1.5 or 20-ampere, fused electrical supply is required. Time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit serving only this appliance be provided Recommended groundfng method Do Not, under any circumstances, remove the power supply cord grounding prong. For your personal safety, this appliance must be grounded. This appliance is equipped with a power supply cord having a 3-prong grounding plug. To minimize possible shock hazard, the cord must be plugged into a mating, 3-prong, grounding- type, wall receptacle, grounded in accordance with the National Electrical Code ANSI/NFPA 70-latest edition and all local codes and ordinances. If a mating wall receptacle is not available, it is the personal responsibility and obligation of the customer to have a properly grounded, 3-prong, wall receptacle installed by a qualified electrician. (See Figure 1,I J-prong grounding-+ype wall receptacle . ....-. . .... . ., ‘.. power supply cord Figure 1 Page 2 Now start... With compactor in room where it will be installed. Product/Floor Damage . Do Not grasp console to move compactor. . Before moving compactor across floor, check that compactor is on shipping base or slide compactor onto cardboard or hardboard. Failure to follow these instructions may result in damage to floor covering or product. 1. Remove compactor from shipping carton. Remove all protective packaging materials such as tape and shipping pads Waxy residue from protective shipping material may be removed with a mild solution of liauid household cleaner and water. cord . ..... :...:. . ... clip 2. r!lI Check that power supply cord is attached to the cord clip on the rear of the compactor. n Place two corner posts from carton on floor near compactor. Open compactor drawer and remove any shipping materials or other items shipped in the drawer. Do Not remove the compactor bag (if installed). Grasp the handle and raise the front of drawer untrl it clears stops. Grasp sides of drawer and lift drawer out of compactor. Place the drawer on the two corner posts. n Place the other two corner posts on the floor to the side of the compactor. Grasp the sides of the compactor cabinet and put compactor on its side on top of the corner posts. Remove the shipping base from the bottom of compactor. n Freestandina installation Go to Step 6. - Undercounter installation The rear wheels are preset for a cabinet opening height of 34” (86.4 cm> (P...