Évaluations - 4, GPA: 4
(
)
)
|
Facilité d'utilisation
Adjust the leveling legs until the compactor is level. 2. Move the compactor close to its final position. Plug the power supply cord into a 3-prong grounded outlet. 3. Carefully move compactor into its final position. Check that compactor is still level. Repeat step 1 if necessary. 4. Grasp sides of compactor drawer and place bottom of drawer into tracks. Lift at the handle so drawer will go over drawer stops. Close drawer. Check if drawer opens freely. If the toe plate rubs against floor, see “Adjusting the Toe Plate” for further instructions. Undercounter installation: NOTE: Installation hardware is not provided with full cabinet models. 1. Measure the height of your cabinet opening. The top of the compactor should be at least 1.8" (3 mm) from the top of the cabinet opening. The rear wheels are preset for a cabinet opening height of 341.4" (87 cm) (Position “A”). To adjust for other cabinet opening heights, loosen screw just enough to clear stud from hole in position “A”. Move the rear wheel and stud to position “B” or “C” as needed for your cabinet opening measurement: Position B: 341.4" to 347.16" (87 to 87.5 cm) Position C: 347.16" to 345.8" (87.5 to 88 cm) Tighten screw. Repeat for other rear wheel. A cabinet locating stud self-tapping screw (pivot) wheel bracket assembly B C 2. Use pliers to lower leveling legs away from cabinet. Adjust legs so there will be a 1.8" (3 mm) to 1.4" (6.4 mm) space between the top of the compactor and the top of the cabinet opening. Stand the compactor upright. 3. For model with cabinet, remove the plastic plugs from the compactor cabinet top. 4. Determine if you want the compactor frame or drawer front flush with the cabinet front. Using the two #8 -18 x 5.16" (8 mm) screws, install the retaining brackets to cabinet top as needed: If the compactor frame is to be flush with the cabinet front, place retaining bracket screws through “A”. If the compactor drawer front is to be flush with the cabinet front, place retaining bracket screws through “C”. If the compactor is to be midway between “A” and “C”, place retaining bracket screws through “B”. 5. Carefully lift the front slightly and roll compactor into the cabinet opening. B A retaining bracket C countertop Using the two #8 -18 x 1.2" (12 mm) screws, fasten the retaining brackets to the underside of the countertop with the mounting screws. If brackets cannot be attached to the underside of countertop, attach mounting clips to brackets. Fasten compactor to cabinet front with mounting screws through mounting clips. Countertop mounting mounting screw retaining bracket retaining clip mounting screw bracket mounting Cabinet-front mounting 6. Grasp sides of compactor drawer and place bottom of drawer into tracks. Lift at the handle so drawer will go over drawer stops. Close drawer. Check if drawer opens freely. If the toe plate rubs against floor, see “Adjusting the Toe Plate” for further instructions. Adjusting the Toe Plate If the toe plate rubs the floor covering, the toe plate clearance may be changed as follows: 1. Mark on each side of the toe plate the amount of toe plate that rubs the floor covering. 2. Remove the drawer from the unit. (See step 3 in the “Unpacking Your Compactor” section.) 3. Use a ruler and a pencil or chalk to draw a line between the marks on each side of toe plate. 4. Use scissors or utility knife to cut toe plate along line. 5. Replace drawer. If toe plate still rubs floor covering, repeat steps 1-4. Changing the Decorative Panel Custom-made panel dimensions 2313.16" (60.5 cm) 145.8" (37.2 cm) Flat panel: A 7.32" (5.6 mm) thick panel is required. This is the same thickness as a standard 1.4" plywood or paneling. 7 .32" (5.6 mm) raised panel ordecorative trim outer section of panel 5 .16" (8 mm) both sides 11.4" (32 mm) 5.16" (8 mm) 145.8" 2313.16" (60.5 cm) Raised panel: The outer section of panel must be 7.32" (5.6 mm) thick to fit into trim. Raised panel dimensions as shown above. Trim for decorative panel Order trim for installation of a custom-made panel through your KitchenAid dealer or by calling the KitchenAid Consumer Assistance Center at 1-800-422-1230. In Canada, call 1-800-807-6777. Trim for custom-made panels available are: Part No. 9871381 (Brushed stainless steel) Part No. 9871382 (White) Part No. 9871383 (Black) Part No. 9871384 (Almond) Part No. 9871600 (Biscuit) (37.2 cm) 10 USING YOUR COMPACTOR Open the drawer Lift and pull the handle or press the drawer opener to open the drawer. wWARNING Explosion Hazard Do not compact any container, aerosol cans, or cloths which might contain insecticide, hair spray, engine starting fluid, paints, liquids, thinners, or any other poisonous or explosive products. Doing so can result in death, explosion, or fire. wWARNING Cut Hazard Do not push items down into compactor with hands or feet. Doing so can result in cuts. OR Put in the trash NOTE: You will not see compacting of trash the first few times you load the compactor. The compactor drawer sho...
Ce manuel est également adapté pour les modèles :Autres appareils de cuisine - KUCC151 (552.19 kb)