Évaluations - 3, GPA: 3.3 ( )

Fabricant : Cleveland Range Taille : 2.62 mb Nom Fichier : Langue d'enseignement:

Do not use steel pads, wire brushes or scrapers to clean stainless steel. 4. Use non-chlorinated cleaners at recommended concentrations. Use only chloride- free cleaners. 5. Soften your water. Use filters and softeners whenever possible. 6. Wipe off cleaning agent(s) and standing water as soon as possible. Prolonged contact causes eventual problems. To learn more about chloride-stress corrosion and how to prevent it, contact the equipment manufacturer or cleaning materials supplier. Developed by Packer Engineering, Naperville, Ill., an independent testing laboratory. Though this is not always practical, softening hard water can do much PRODUCT VALVE Daily - clean product valve as follows: SCRAPER BLADES To remove and clean scraper blades: Fig. 1 Fig. 2 Fig. 3 To Remove Scraper Blade 1. Insert tool that is provided as shown in Fig. 2. 2. Pull up on spring arm until arm clears groove in Pin B. 3. Spring is now disengaged, gently release spring to remove scraper blade. To Install Scraper Blade 1. Slide scraper blade and spring onto Pin A as shown in Fig. 1. 2. Hook spring arm and pull up. 3. Using tool, engage spring arm into groove on Pin B. Scraper blade is now in place. 1. Remove scraper blades using the tool to release the spring from the retaining pin and sliding the blade off the shaft. 2. Place parts in a pan of warm water to soak. 3. Clean in a sink, using a warm water and mild detergent solution. 4. Rinse with fresh water. 5. Allow to dry thoroughly on a flat, clean surface. 1. Open product valve. 2. Disconnect air hoses. 3. Remove air cylinder 4. Remove valve tee. 5. Remove all O-rings. 6. Clean air cylinder, do not submerge in water. Wipe clean and sanitize. 7. Clean and sanitize tee and O-rings. 8. Grease and reinstall O-rings. 9. Reinstall tee to kettle outlet. 10. Reinstall air cylinder to bottom of tee. 11. Reconnect air hoses. 12. Close valve and check for alignment. AGITATOR To remove and clean agitator (two-person job): 1. Remove scraper blades. 2. Rotate agitator until pull pin is on top side. 3. Turn power OFF 4. Pull pin out. 5. Slide coupling toward kettle wall, and carefully lift agitator pulling back to lift out. 6. Clean in a sink, using a warm water and mild detergent solution. 7. Rinse with fresh water. QUAD RING To clean agitator quad ring: 1. Remove retaining knobs. 2. Slide shaft seal retainer plate and quad ring away from kettle body. 3. Clean quad ring, shaft, and seal retainer plate with clean cloth. 4. Rinse with fresh. 5. Apply light coat of food safe grease to both sides of the quad ring. 6. Slide quad ring back into original position, making sure it does not twist. 7. Slide retainer plate back toward kettle, replacing retaining knobs. 8. Tighten with hand pressure only. AGITATOR BUSHING With agitator out, remove bushing by: 1. Remove bushing by turning 1/4 turn and pulling away from the kettle wall. 2. Clean, rinse and sanitize bushing and bushing mounting area. 3. Lubricate metal surfaces with food safe grease. 4. Install bushing by locating retaining pin and sliding bushing on. 5. Rotate to lock into position. Bushing_ _Slot -1 =n V [ Agitator Retaining Shaft pin / SERVICE PARTS SCRAPER BLADES ITEM NO. PART NO. DESCRIPTION QTY. 1. KE54602 SCRAPER BLADE...............7 2. KE54608 SPRING .......................7 3. KE01976 SPRING REMOVAL TOOL ........1 AGITATOR SEAL ASSEMBLY ITEM NO. PART NO. DESCRIPTION 1. KE01911 RETAINING KNOBS..... 2. KE54592 SEAL RETAINER PLATE . . 3. FA05002-8 "O" RING.............. 4. KE54594 PIN .................. 5. KE54583 COUPLING............ 6. KE54593 IDLER PIN ............ 7. KE54590 BUSHING ............. QTY. OPERATING CONTROLS ITEM NO. PART NO. DESCRIPTION QTY. 1. KE54531 AGITATOR STOP......................1 2. KE54530 AGITATOR START.....................1 3. KE54529 POWER ON/OFF SWITCH...............1 4. KE54532 SPEED CONTROL.....................1 PRESSURE RELIEF ASSEMBLY ITEM NO. PART NO. DESCRIPTION QTY. 1. FA05049 MALE CONNECTOR, 1/2” PIPE - 1/4” TUBE............................1 2. FI00151 STREET ELBOW, 1/2" .............................................2 3. FI00178 TEE, 1/2" FPT, BRASS.............................................1 4. KE54941-5 SAFETY VALVE, 50 PSI, 1/2" (NORTH AMERICA) .......................1 KE54941-31 SAFETY VALVE, 50 PSI, 1/2", (EUROPE) ..............................1 5. KE54223 BLOW DOWN TUBE .............................................. 1 HINGE ASSEMBLY ITEM NO. PART NO. DESCRIPTION QTY. 1. - 11 KE50597-1 KE50597-2 KE50597-3 KE50597-4 KE50597-5 1. KE50822 2. KE51217 3. KE50121-2 KE50121-1 4. KE50823-1 5. KE50824 6. KE50819-1 7. KE50820 8. KE50819 9. FA11284 10. FA11507 11. SK50418 12. KE50151-2 Hinge Assembly 25 - 40 Gallon, 20 Gallon Full Jacketed ............................. 60 - 80 Gallon, 30 - 40 Gallon Full Jacketed ......................... 100 - 150 Gallon, 60 - 100 Gallon Full Jacke...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :