Log:
Évaluations - 1, GPA: 4 ( )

Instructions Fisher & Paykel, Modèle IZONA RB905

Fabricant : Fisher & Paykel
Taille : 2.03 mb
Nom Fichier :
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


For the F&P prefinished panel with a .“ (6 mm) reveal: 18 .” (476 mm) Height of the False Panel F&P prefinish panel width is 35 .” (896 mm) F&P prefinish panel height (D) is 18 .” (476 mm) Installation diagrams for illustration purposes only Drawer Panel height of False Panel A A False Panel width of Panels D height of Drawer Panel /”(4 mm) SIDE VIEW Benchtop Drawer panelFalse panel A D C B Integrated Panel material Maximum weight of 15.5 lb (7 kg). Height of Drawer Panel Dimension A Reveal dimension B Height between top of spacer block and underside of benchtop C D Drawer panel height To calculate D complete the following equation: D = B - A - C i.e. For the F&P prefinished panel with a .“ (6 mm) reveal: 18 .” (476 mm) Height of the False Panel F&P prefinish panel width is 35 .” (896 mm) F&P prefinish panel height (D) is 18 .” (476 mm) Installation diagrams for illustration purposes only Drawer Panel height of False Panel A A False Panel width of Panels D height of Drawer Panel /”(4 mm) SIDE VIEW Benchtop Drawer panelFalse panel A D C B 6 PANEL PREPARATION / -/”(16 - 20 mm) panel thickness (.”[18 mm] recommended). Adequately sealed to withstand moisture (122OF/50OC @ 80% RH) The following information is required to correctly define your drawer panel height: Data Source Bottom face of Your kitchen designer Your kitchen designer Drawer panel to top of spacer block Your kitchen designer (Min. 6” [152 mm]) (Max. 7 .” [184 mm]) Calculated from A, B & C = 26 .” (666 mm) - .” (6 mm) -7 .” (184 mm) Determine the height of the false panel according to your individual kitchen cabinetry requirements maintaining a /” (4 mm) gap between panels. 2 2 1 3 3 3 30 /” (764 mm)** 1 /” (50 mm)* 4” (102 mm) max. /” (16 mm) 11” (280 mm) 8 .” (215 mm) 8 .” (215 mm) max. 33 /” (862 mm) min. 33 /” (860 mm) 1” (25 mm) 3” (76.5 mm)* 1 /” (40 mm) 2 3 4 1 1 2 7 CREATE CUTOUTS IN FRAME 11 MOVE PRODUCT INTO CAVITY 9 ATTACH OUTLET VENT DUCT If the cabinetry does not already have cutouts, ensure the modifications below are made. Important! Ensure the power cord is clipped in place. Important! Ensure a minimum of 3 screws per side are used. The rear screws must always be used. Horizontal fixing is also optional. 8 LOCATE & SECURE INSTALL BRACKETS *Cutout dimensions referenced from inside face of cabinetry frame. **Only with cabinetry with internal shelf 10 ATTACH POWER CORD & TRIM BRACKETS Important! Cut outlet duct to be flush with top of spacer block. Important! Note correct orientation of bracket. 12 FIT DRAWER PANEL ATTACHMENT HOOKS 1 2 3 1 2 3 4 5 6 7 8 2 1 1 /” (46 mm) 2 1 9 mm x 3 /“ (2.5 mm) (35 .” [902 mm]) /” (1 mm) /” (5 mm) /” (18 mm) 12 .” (311 mm) 12 .“ (311 mm) 16 /” (414 mm) X / - /” (16 - 20 mm) 11 MOVE PRODUCT INTO CAVITY 13 ATTACH DRAWER PANEL TO FRONT OF DRAWER Important! Do not screw in trim brackets at this stage. Hook drawer panel onto drawer front channel Close the drawer and check vertical clearances Remove the panel and adjust the TOP attachment hooks as necesary Replace panel on drawer and confirm vertical clearances Slide panel to achieve even horizontal clearances Open drawer and clamp panel onto drawer by tightening the BOTTOM attachment hook Close the drawer and ensure it is flush with adjacent cabinetry. If not, the product may have to be pulled back or forward. Important! Be careful not to damage power supply cord when pushing product into cavity. 12 FIT DRAWER PANEL ATTACHMENT HOOKS Ensure there is clearance between panel and cabinetry when drawer is fully closed Attach handle as necessary. Ensure all screws are flush with panel surface. X = 7 /” (194mm) - C, where C is bottom face of panel to top of spacer block, see 6 .. .. /” (4 mm) .. /” (2 mm) .. .. 14 18 SECURE PRODUCT TO CABINETRY FINAL CHECKLIST 16 ATTACH FALSE PANEL Important! Ensure you check basic operation and perform the final checklist. Attach the false panel securely as recommended by the cabinet maker. Important! The false panel needs to be removable for servicing. 15 17 CHECK OPERATION Open drawer and secure product to cabinetry using four Trim brackets and screws. ATTACH TRIMS TO SIDES OF CABINETRY 840509B FRAMED CABINETRY 08.08 18 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER Has all packaging been removed from the appliance? Is the appliance securely fastened to the cabinetry? Does the drawer slide freely and close properly? Has the outlet duct been installed correctly? Is the appliance level? Are the panels securely attached? Have the panels been properly aligned for correct operation and appearance? Are all clearances even? Is there clearance between drawer and cabinetry frame? Has the power cord been plugged into a properly grounded 3-prong outlet, which has been installed in accordance with all applicable electrical codes? OPERATION: Is the control panel lit? Can you hear the compressor motor running? When a hand is placed near the toe kick, can airflow be felt under front right-hand side of appliance? Have yo...

Ce manuel est également adapté pour les modèles :
Autres appareils de cuisine - IZONA RB365 (2.03 mb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories