Évaluations - 2, GPA: 4 ( )

Fabricant : Hatco Taille : 814.14 kb Nom Fichier : Langue d'enseignement:

For safe and proper operation locate the unit indoors where the ambient air temperature is a minimum of 70°F (21°C). OPERATION ALL MODELS CAUTION Some exterior surfaces on the unit will get hot. Use caution when touching these areas to avoid injury. 1. Plug warmer into a properly grounded electrical outlet of the correct voltage, size and plug configuration. See SPECIFICATIONS for details. 2. Turn the Power Switch to the ON position. See Figures 6 & 7. 3. Turn the Temperature Control to the desired temperature setting. 4. Allow unit 15-20 minutes to reach operating temperature. 5. Open top door and fill unit with chips. 6. At the end of the day or shift, turn unit off and allow to cool down. Clean as required. FLAV-R-FRESH Figure 6. Control Panel FDW-1-MN Temperature Control Power Switch Temperature Gauge FLAV-R-SAVOR Figure 7. Control Panel FST-1-MN Temperature Control Power Switch Temperature Gauge 5 Form No. MNM-0702 MAINTENANCE GENERAL Hatco Macho Nacho™ Chip Warmers are designed for maximum durability and performance, with minimum maintenance. WARNING To avoid any injury, turn the power switch off at the fuse disconnect switch/circuit breaker or unplug the unit from the power source and allow to cool completely before performing any maintenance or cleaning. CLEANING To preserve the bright finish of the unit, it is recommended that the exterior and interior metal surfaces be wiped daily with a damp cloth. Stubborn stains may be removed with a good stainless steel cleaner or a non-abrasive cleaner. CAUTION Use only non-abrasive cleaners. Abrasive cleaners could scratch the finish of your unit marring its appearance and making it susceptible to soil accumulation. Clean the glass using a common glass cleaner. NOTE: For better access to the inside of the unit, the rear door panel assembly can be removed by loosening the thumbscrews on each side of the door panel assembly and lifting the assembly up and off. Be sure to tighten thumbscrews securely when installing the door panel assembly. See Figure 8. DISPLAY LIGHT BULB REPLACEMENT The display light is an incandescent light bulb which illuminates the warming area. The bulb has a special coating to guard against injury and food contamination in the event of breakage. 1. To replace a light bulb, disconnect the power supply and wait until the unit has cooled. 2. Bulbs have a threaded base. Unscrew the light bulb from the unit and replace it with a new specially coated incandescent bulb. NOTE: Hatco shatter-resistant light bulbs meet N.S.F. standards for food holding and display areas. For 100 and 120 volt applications, use Hatco part #02.30.043.00. For 220 or 240 volt applications, use Hatco part #02.30.058.00. FLAV-R-SAVORHOLDINGAND DISPLAY CABINET Thumbscrews (Two on each side) Figure 8. Removing Door Panel Assembly WARNING Only light bulbs which meet or exceed N.S.F. standards, specifically designed for food holding areas must be used. Breakage of light bulbs not specially coated could result in personal injury and/or food contamination. WARNING If service is required on this unit, contact your Authorized Hatco Service Agent, or contact the Hatco Service Department at 800-558-0607 or 414-671-6350; fax 800-690-2966 or International fax 414-671-3976. WARNING This product has no “user” serviceable parts. To avoid damage to the unit or injury to personnel, use only Authorized Hatco Service Agents and Genuine Hatco Parts when service is required. WARNING Genuine Hatco Replacement Parts are specified to operate safely in the environments in which they are used. Some aftermarket or generic replacement parts do not have the characteristics that will allow them to operate safely in Hatco equipment. It is essential to use Hatco Replacement Parts when repairing Hatco equipment. Failure to use Hatco Replacement Parts may subject operators of the equipment to hazardous electrical voltage, resulting in electrical shock or burn. Form No. MNM-0702 6 HATCO LIMITED WARRANTY 1. P...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :