Évaluations - , GPA: ( )

Instructions Wells, Modèle WPP-6, WPP-10

Fabricant : Wells
Taille : 903.88 kb
Nom Fichier :

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Wipe lid and stirrer components with a sponge or soft cloth dampened with mild detergent. Rinse by wiping with a sponge or soft cloth dampened with clear water. Allow to air dry. 6. Wipe inside and outside of cabinet, drop door and crumb tray with a sponge or soft cloth dampened with mild detergent. Rinse by wiping with a sponge or soft cloth dampened with clear water. Allow to air dry. NOTES: a. Use care when cleaning doors to prevent scratching. b. Do not wipe heat lamp if it is hot. c. Use care that no water is splashed into kettle receptacle or heat lamp socket. 7. Reinstall kettle lid. Reassemble stirrer, then reinstall kettle. Reinstall drop door, then slide crumb tray in place. Procedure is complete. 232 306223 Owners Manual WPP- Series Popcorn Popper 6 TROUBLESHOOTING SUGGESTIONS 232 306223 Owners Manual WPP- Series Popcorn Popper PROBLEM No power to unit Does not pop popcorn Popcorn does not pop completely Heat lamp does not light Base heater does not provide heat Cannot tilt kettle fully Stirrer wand interfering with kettle tilt Stirrer does not rotate POSSIBLE CAUSE Power cord unplugged Circuit breaker tripped Power cord or plug damaged Kettle switch OFF Kettle plug not securely plugged into twist- lock receptacle Damaged kettle switch Damaged kettle internal components Some brands of popcorn, or popcorn that is out-of-date may not pop completely. NOTE: even the freshest example of the very best brand may not always pop 100% of its kernels No or insufficient oil added at start of cycle. Warmer switch OFF Heat lamp loose in socket or burned out Damaged warmer switch Warmer switch OFF Damaged warmer switch Warmer element or wiring damaged Kettle normally tilts only slightly past vertical Kettle misassembled to hangers Power cord twisted Stirrer misassembled or contaminated with built-up cooking debris Position cam loose or damaged Damaged position switch or wiring Stirrer only rotates when kettle switch is ON Kettle switch OFF Stirrer loose on gear drive shaft Stirrer motor damaged SUGGESTED REMEDY Plug power cord into appropriate receptacle Reset circuit breaker Replace power cord assembly Press kettle switch to “ON” Properly connect kettle cord Replace kettle switch Replace kettle assembly. Always use fresh, quality popcorn Refer to popcorn manufacturer’s recommendations for proper quantity of oil. Press warmer switch to “ON” Tighten or replace heat lamp Replace warmer switch Press warmer switch to “ON” Replace warmer switch Repair wiring and/or replace warmer element No action required Properly reinstall kettle Disconnect plug, straighten cord, reconnect plug Clean stirrer components and reassemble properly Reconnect or replace position cam Repair wiring and/or replace position switch No action required Press kettle switch to “ON” Reattach stirrer to gear drive shaft Replace motor and gear drive assembly 7 ADJUST STIRRER NEUTRAL POSITION With the kettle switch OFF, the stirrer should land at a position that allows the kettle to rotate without binding on the stirrer wand. If the stirrer wand does not land positioned left to right, adjust the positioning cam: 1. Disconnect unit from electric power. Remove the top panel. Raise the kettle lid until it is captured by the magnetic holder. 2. Spin the gearmotor fan by hand until the stirrer wand is positioned left to right (I.e. parallel to the front of the cabinet). 3. Loosen the positioning cam nut and locknut. Turn the cam until it depresses the pin of the positioning switch. Tighten the cam nut and lock nut. 4. Reconnect unit to electric power. Press the kettle switch to “ON”. Wait approximately 5 seconds, then press the kettle switch to “OFF”. The stirrer motor will run until the positioning cam activated the positioning switch. 5. If the stirrer wand stops in the proper left-to-right position, procedure is complete. Otherwise, repeat steps 1 through 4. CHANGE HEAT LAMP 1. Press warmer switch “OFF”. Allow unit to cool before replacing lamp. 2. Squeeze front and rear portions of guard until the front hook clears the slot. Slide the rear hook from its slot, then remove the guard. 3. Unthread old heat lamp from its socket and discard. 4. Thread new heat lamp into socket. IMPORTANT: Use only 400W safety-coated lamp 5. Reinstall guard. CAUTION: INJURY HAZARD Disconnect appliance from electrical power before performing any of these procedures. Adjust Positioning Cam CAUTION: BURN HAZARD Lamp may be hot. Allow lamp to cool before replacing. Change Heat Lamp MAINTENANCE INSTRUCTIONS 8 MAINTENANCE INSTRUCTIONS 8 EXPLODED VIEWS 9 232 306223 Owners Manual WPP-Series Popcorn Popper WIRING DIAGRAM 10 WIRING DIAGRAM 10 PARTS & SERVICE DESCRIPTION PART NO. LADLE, 1.5 oz. 23166 LADLE, 4 oz. 23167 SCOOP, POPCORN 23168 IMPORTANT: Use only factory authorized service parts and replacement filters. For factory authorized service, or to order factory authorized replacement parts, contact your Wells authorized service agency, or call: Wells Manufacturing Co. 2 Erik Circ...