Évaluations - 2, GPA: 4.5
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
Make sure all Ventilation Openings (B) have a minimum clearance of 10” (25cm.) from surrounding walls and other appliances. Before using your SNO Ice Cream Maker, remove the Bowl (C) and Churn (H) and wash in warm water. The Lid (E) and Motor Drive (G) are attached and should be cleaned with a damp cloth. Do not place any part in the dishwasher. Thoroughly dry the Bowl (C) inside and outside and the blade (H) into the Lid/ Churn motor assembly (E/G) and set aside. Plug the Power Cord (K) into a standard electrical outlet (110/120V-60Hz). With the Lid/Churn Motor Assembly (E/G) off, pour ingredients according to the selected recipe into bowl (C). Replace Lid/Churn Motor Assembly (E/G). Turn the main power Switch (I) located at the rear of the appliance on. This turns on the cooling compressor and Timer Display Panel (J). Next, set the required time. The Timer Display (J) will automatically display the time set from the previous batch. To change and set the time, press the yellow timer set switch. By pressing and releasing, single minutes can be set, pressing and holding the yellow timer set switch down, will advance the minutes quickly. The time can be set from 0-60 minutes. Recommended time is 25-30 minutes. The previously set time may be changed by pressing the yellow timer set switch a second time within 6 seconds of the first setting. Once the time has been set, press the Red Start/Stop Switch to start the Churn Blade (H). When the set time has elapsed to “0” on the Timer Display (J), the buzzer will buzz 5 times alerting you that the ice cream is done. Press the Red Start/Stop Switch to stop the churn. Remove the Lid/Churn Motor Assembly (E/G) and check the ice cream. If it is ready shut the Main Power Switch (I) and remove the ice cream. Always use plastic or wooden utensils, never use metal to avoid damaging the Bowl (C). The Yellow Timer Set Switch works as a timer only; it does not turn the churn or cooling motor “Off” automatically. Both must be turned “On” and “Off” manually. If the ice cream needs more time, do not turn “Off” the Main Power Switch (I). Place the Lid/Churn Motor Assembly (E/G) in position, set the additional time required and press the Red Start/Stop Switch to start the churn. If the Churn Motor (G) was not turned “Off” after the set time elapsed, the Churn Blade (H) will continue until the blade becomes stuck in the frozen ice cream. 30 seconds after being stuck, the buzzer will buzz and the Timer Display (J) will flash. After 5 minutes, the Churn Motor (G) will shut “Off” automatically preventing any damage to the motor. The buzzer and flashing display will continue. To, reset the machine, press the Red Start/Stop Switch and turn “Off” the Main Power Switch (I). The churn blade and ice cream at this point will be frozen solid and will require defrosting before it can be removed. Be careful not to damage the removable bowl. Always unplug the unit from the outlet when not in use. If the Main Power Switch(I) is turned “Off”, always allow at least 3 minutes, before turning it back ”On”. Always keep the Ice Cream Maker in an upright position to avoid reduction of cooling performance. There will be a variation in the time it takes for a batch of ice cream to freeze, depending on the amount and on the temperature of ingredients used. If you want quicker results, use less ingredients and/or refrigerate the ingredients before use. For any faults which cannot be cleared and for further assistance and service the contact information is shown on the next page. Appliance Technical Data Voltage: Power: Cooling Temperature: Frozen dessert batch: Dimensions : Shipping dimensions: Net weight: Gross weight: 110/120V-60Hz 3.30 Amp 235W or about . HP -11F or -24C 2 Quarts+ (about 2 Liters) 11’’W x 20’’L x 15’’L x 13’’H (28cm.W x 38cm.L x 33cm. H) 16 .”W x20”Lx17 .”H (41cm.W x 51cm.L x 45cm. H) 39Lbs. (17.75Kg.) 43Lbs. (19.5 Kg.) ONE YEAR LIMITED WARRANTY This WHYNTER ice cream maker is warranted, to the original owner within the 48 continental states, for one year from the date of purchase against defects in material and workmanship under normal use and service. Should your WHYNTER ice cream maker prove defective within one year from the date of purchase, return the defective part or unit, freight prepaid (within two months of purchase; after two months to one year, customer will be responsible for freight cost to Whynter’s service department), along with an explanation of the claim to Whynter LLC. Please package the ice cream maker carefully in its original packaging material to avoid damage in transit. Please retain original box and packaging material. Under this warranty, Whynter will repair or replace any parts found defective. This warranty is not transferable. After the expiration of the warranty, the cost of labor and parts will be the responsibility of the original owner of the unit. THIS WARRANTY DOES NOT COVER: . Acts of God, such as fire, flood, hurricanes, earthquakes and tornadoes. . D...