Log:
Évaluations - 3, GPA: 4.3 ( )

Instructions Avanti, Modèle AVANTI IM15SS

Fabricant : Avanti
Taille : 467.51 kb
Nom Fichier : im15ss.pdf
Langue d'enseignement: enes
Aller à la télécharger



Facilité d'utilisation


• Connect tubing (supplied with unit) to the nearest cold water source. Connect sufficient tubing to the unit to allow the appliance to be moved freely for cleaning and service. Also make sure that the tubing is not pinched or damaged during transportation. • Position unit to allow free airflow through the front grill (see sketch 1). Wipe out inside of unit and ice bucket with a damp cloth. SKETCH 1 . Reversing the door swing of your ice maker This appliance has the capability of the door opening from either the left or right side. The unit is delivered to you with the door opening from the left side. Should you desire to reverse the opening direction, please call customer service for reversal instructions. Operating your ice maker . Initial start-up operation 1. Plug the appliance into a 115/120v polarized and grounded wall electrical outlet. 2. Place the on-off switch in the “on” position. 3. Make sure the water supply is on. As soon as the inner mechanism reaches the proper temperature, the icemaker mechanism will fill the mold with water. 4. The first cubes may be small because of air in the water line. Later cubes will be of standard crescent moon type size. 5. Approximate time for the first cycle is between 30-40 minutes. 6. Each cycle approximately will take 140 ml of water so you should have a full tray, after 11 hours. Important: throw away all ice cubes made during the first 3 hours of operation. SKETCH 2 • When the ice bucket is full, the ice making mechanism will automatically shut off. However the system will continue to cool and maintain the cubes supply. • Ice delivery may be interrupted by raising the metal arm into an upright position (see sketch 2) • If the icemaker is not used regularly, it is recommended that the ice bucket be emptied periodically to insure fresh ice. • Sometimes the cubes may appear cloudy. This is cause of no concern and has nothing to do with the taste or chemical make-up of the water. • The front grill should be kept free of dust and lint to permit free airflow. • This unit should be defrosted approximately every 4-6 weeks or when frost on the ice maker walls is excessive or .” thick. To defrost, turn the unit off, remove cubes and keep door open at least two inches. . Installing the Safety Door Latch (Optional) Affix the safety door latch to the unit by attaching the assembly to the unit using the screws included (see diagram). LATCH PIN Remove the plastic hole covers from the top left hand side of the unit. Attach the safety latch arm to the unit by inserting the two (2) flat head screws in the top two (2) screw holes on the top left hand side of the unit. Remove the plastic hole cover from the top left hand side of the door and insert the safety pin. Adjust the latch by moving either one or both flat screws used on the top left hand of the unit until latch locks firmly. Care and maintenance . Cleaning your ice maker • Turn the switch control to "off", unplug the ice maker and remove bucket. • Wash the inside with a warm water and baking soda solution. The solution should be about 2 tablespoons of baking soda to a quart of water. • Wash the bucket with a mild detergent solution. • The outside of the ice maker should be cleaned with mild detergent and warm water. • The condenser coils should be vacuumed when they are dusty or dirty. Caution Failure to unplug the ice maker could result in electrical shock or personal injury. . Power failure Most power failures are corrected within a few hours and should not affect the temperature of your ice maker if you minimize the number of times the door is opened. If the power is going to be off for a longer period of time, you need to take the proper steps to disconnect your appliance. . Vacation time/storage 1. Shut off water supply at the main water valve. 2. Disconnect the water supply line from valve. 3. Allow unit to run for an hour or two until all remaining ice cubes have been ejected. 4. Disconnect unit from main power source. 5. Dry out excess water from ice maker assembly 6. Leave the door open at least two inches. . Moving your ice maker • Securely tape down all loose items inside your ice maker. • Turn the leveling screws up to the base to avoid damage. • Tape the door shut. • Be sure the ice maker stays in the upright position during transportation. . Energy saving tips • The ice maker should be located in the coolest area of the room, away from heat producing appliances or heating ducts, and out of the direct sunlight. Problems with your ice maker? You can solve many common ice maker problems easily, saving you the cost of a possible service call. Try the suggestions below to see if you can solve the problem before calling the servicer. Troubleshooting guide Problem Possible cause Ice maker does not operate. Not plugged in. The circuit breaker tripped or a blown fuse. The ice maker power switch is set at "off". Not producing ice Airflow to front grill blocked. The ice maker arm is set to the off position. Water su...


Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories