Évaluations - , GPA:
(
)
)
Fabricant : Brinkmann
Taille : 2.7 mb
Nom Fichier : 892e971f-6040-4af5-b849-48db99ed5e3a.pdf
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Facilité d'utilisation
If found, replace the burner. • DO NOT obstruct the flow of combustion and ventilation air. Burner tubes can become blocked by spiders and other insects building their nests. Blocked burner tubes can prevent gas flow to the burner and could result in a burner tube fire or fire beneath the grill. To clean the Burner Assembly follow these instructions to clean and/or replace parts of burner assembly or if you have trouble igniting the grill. 1. Turn gas off at control knobs and LP cylinder tank valve. 2. Remove cooking grills and heat distribution plates. 3. Remove screws from beneath each burner "foot" using a screwdriver. 4. Carefully lift the burner up and away from valve openings. 5. Use a narrow bottle brush or a stiff wire bent into a small hook to run through each burner tube and flame port several times. NOTE: Wear eye protection when performing procedure 6. 6. Use compressed air to blow into burner tubes and out the flame ports. Check each port to make sure air comes out each hole. 7. Wire brush entire outer surface of burner to remove food residue and dirt. 8. Check burner for damage, if any large cracks or holes are found replace burner. IMPORTANT: Burner openings must slide over valve nozzles. 9. Carefully replace burner. 10. Replace screws beneath each burner foot and follow the "Gas Leak Testing" section of this manual. Relight burners to verify proper operation. 11. Replace heat distribution plates and cooking grills. Debris Burner Orifice Valve Nozzles PROPER BURNER OPERATION COOKING GRILLS • Clean with mild soap detergent and water. A brass bristled brush or a nylon cleaning pad can be used to remove residue from the stainless steel surfaces. Do not use steel wire bristles to clean the cooking grills. Steel can cause the finish to chip or crack. DO NOT use a commercial oven cleaner. HEAT DISTRIBUTION PLATES • Periodically, it may be necessary to inspect and clean the heat distribution plate to prevent excess grease build-up. When the grill is cold, remove the cooking grill. Inspect the heat distribution plates and replace if broken or damaged. Do not allow heat distribution plates to become damaged to the extent that they may fall through onto the burners. Replace the heat distribution plates and cooking grills and light the burners. Operate the grill on "HIGH" for 10 minutes to remove the excess grease. WARNING TRANSPORTING AND STORAGE: • Never move a grill when it is hot or when objects are on the cooking surfaces. • Make sure that cylinder valve is shut off. After moving the grill check that all gas connections are free of leaks. Refer to instructions for Leak Testing. • DO NOT store a spare LP gas cylinder (filled or empty) under or near the grill. • Never store flammable liquids or spray canisters under or near the grill. • DO NOT extinguish grease fires using water. • If the outdoor cooking gas appliance is not in use, the gas must be turned off at the supply cylinder. • Storage of an outdoor cooking gas appliance indoors is permissible only if the cylinder is disconnected and removed from the outdoor cooking gas appliance. • Cylinders must be stored outdoors out of reach of children and must not be stored in a building, garage or any other enclosed area. • When removing the grill from storage, spider webs or other debris may be blocking the burner. See "Burner Assembly/Maintenance" under Proper Care and Maintenance. BEFORE STORING YOUR GRILL: • Ensure that the cylinder valve is fully closed. • Clean all surfaces. • Lightly coat the burners with cooking oil to prevent excess rusting. • If storing the grill indoors, disconnect the LP tank and leave the LP tank OUTDOORS. • Place a protective cap cover on the LP tank and store the tank outdoors in a well ventilated area out of direct sunlight. • Clean burner prior to use after storing, at the beginning of grilling season or after a period of one month not being used. Spiders and insects like to build nests in burner tubes (especially during colder months). These nests can cause fires in burner tubes or under grill. • If storing the grill outdoors, cover the grill with a grill cover for protection from the weather. A grill cover may be ordered directly from Brinkmann by calling 800-468-5252 or 800-527-0717. TROUBLE SHOOTING Problem: Possible Causes: • Burner will not light 1. Check LP cylinder fuel level. 2. Bad electrode spark. Check to see if the grill will match light. Electrode or collector may need adjustment. 3. Burner may not be properly seated. 4. Burner may be obstructed. 5. The cylinder valve may be closed. 6. Regulator is not properly seated on cylinder valve. • Fire at control knob 1. Burner holes may be obstructed. See section on "Burner Assembly/Maintenance" under Proper Care and Maintenance. 2. Burner is improperly seated on control valve. 3. Gas connections may be loose. Leak Check and tighten all connections. • Yellow Flames at burner 1. Burner is obstructed. See section on "Burner Assembly/Maintenance" under Proper Care an...