Évaluations - 5, GPA: 3.8
(
)
)
|
Facilité d'utilisation
This fixture has been designed to give you many years of beauty and service. Please email questions and comments to: catalogroom@westinghouselighting.com. NOTE: Carefully unpack fixture and parts. Make sure all parts are included before discarding any packing materials (see figure 1). WARRANTY INFORMATION This Westinghouse Lighting Fixture carries a limited lifetime warranty against defects in materials and workmanship. In addition, this warranty covers corrosion, tarnishing and discoloration of metal components. This warranty is in lieu of all other warranties expressed or implied. This warranty does not cover acts of nature such as lightning damage, nor does it cover damages caused through abuse, improper installation, surges in electric currents, or acts of third parties. This warranty does not cover broken glass. If fixture is received with broken glass, please call Westinghouse Lightning for free replacement. This warranty does not cover costs of removing and re-installing the light fixture. If this fixture fails for any reason covered by this warranty, simply return the fixture with a copy of the original sales receipt, freight prepaid and Westinghouse Lighting, at its option, shall repair or replace the fixture or refund the purchase price. WARNING ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY. Read and follow instructions exactly as shown. If instructions are unclear, do not proceed. Contact a qualified electrician. Read all instructions before beginning. Proper wiring is essential for safe operation of this fixture. When cutting or drilling into walls or ceilings, do not damage electrical wiring, gas lines, or water lines. If any of the fixture or wiring components are damaged, do not install fixture. Return to place of purchase. For fixtures provided with 75° C or 90° C supply wire warning only. (These warnings are provided on the U.L. label and on the fixture carton.) Risk of fire. Most dwellings built before 1985 have supply wires rated 60° C. Consult a qualified electrician before installing. NOTE: For fixture employing a grounded convenience outlet. This fixture employs a grounded type receptacle and is not intended for connection to a two wire ungrounded source of supply. Applicable only to portable lamps: To reduce the risk of electrical shock, all portable lamps have a polarized plug (one blade is wider than the other). This plug will fit into a polarized outlet only one way. If plug does not fit, reverse the plug. If it still does not fit, contact a qualified electrician. Never use with an extension cord unless plug can be fully plugged into the extension cord. Do not alter the plug. 2 12 pg_W-171_EFS 11/28/04 8:25 PM Page 3 3 FIGURE 1. *NOT SUPPLIED Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to this fixture. *OUTLET BOX (C) GREEN GROUNDING SCREW (F) WIRE CONNECTORS (E) GROUND WIRE *OUTLET BOX SCREWS (D) MOUNTING SCREWS (A)MOUNTING BAR (B) SIDE HOLE (G) CANOPY (I) CAP NUTS (K) KEY SLOTS (J) INSULATION (H) 12 pg_W-171_EFS 11/28/04 8:25 PM Page 4 MOUNTING AND WIRING INSTRUCTIONS CAUTION: For fixtures labeled for outdoor and wet location use, provide a water-tight seal between the fixture and the mounting surface by using silicone or similar caulking. NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures meet all UL specifications. 1. Turn off power at circuit box to avoid possible electric shock. 2. Thread mounting screws (A) into mounting bar (B) approximately 1/4 inch (see fig. 1). 3. Secure mounting bar (B) to outlet box (C) with outlet box screws (D) (not included). 4. Identify color coding of fixture wires (see fig. 2). 5. To connect wires, take black fixture wire (group A from fig. 2) and place evenly against black outlet box wire. Do not twist wires. 6. Fit wire connector (E from fig. 1) over wires and twist until there is a firm connection. If wire connector (E) easily comes off, reattach and check again for a firm connection . 7. Repeat steps 5 and 6 with the white (group B from fig. 2) fixture wires and outlet box wires. 8. Partially thread green grounding screw (F) into side hole (G) on mounting bar (B) (see fig.1). 9. Wrap ground wire from fixture and ground wire (metal or green wire) from outlet box (C) around green grounding screw (F) on mounting bar (B). 10. Tighten green grounding screw (F). Do not over tighten. 11. Tuck wires inside outlet box (C). FIXTURE ASSEMBLY INSTRUCTIONS 1. Line up holes in insulation (H) with holes in canopy top (I) (see fig. 1). 2. Raise canopy (I) to ceiling, allowing mounting screws (A) to protrude through key slots (J) in canopy top (I), and secure with cap nuts (K). 3. Install lamp(s). Do not exceed recommended wattage. 4. Turn power back on at circuit box. 4 12 pg_W-171_EFS 11/28/04 8:25 PM Page 5 LES INSTRUCTIONS D'ASSEMBLAGE DE L'APPAREIL D'ECLAIRAGE POUR UTILISATION EXTERIEURE Felicitations ! Vous avez achete un produit de Westin...