|
Facilité d'utilisation
This will prevent the entry of cold air by means of conduction through the total bottom of the appliance. (see Figure 32). CAUTION: Air inlet ducts are not to terminate in attic space. Note: Glass door may be heavy for some individuals. If this is the case, please request help from someone else. The M36E, VM36E, M42E and VM42E B-vent fireplaces are approved for use with optional bi-fold glass doors (see Accessories, page 27). The glass panels may be ordered and installed anytime after the fireplace installation is complete. Follow these steps to install left and right panels: 1. With the handle at the bottom, completely fold the panel on its hinges. 2. With the handle facing the center of the firebox opening, insert the lower pivot pin on the glass door panel into the hole in pivot plate on the bottom edge of the fireplace opening (see Figure 33). 3. Keeping the folded door tilted, slide the upper two pins into the guide track found under the upper facial edge of the firebox opening. 4. Tilt the glass assembly fully vertical until the outer pivot pin snaps into the mounting hole in the upper spring clip (see Figure 33). INSTALLING OPTIONAL GLASS DOOR ACCESSORY CAUTION: Use only glass doors certified for use with this appliance. Figure 31 - Air Kit Handle Location Air Kit Handle Side Framing Side Framing Caulk Here Pack Insulation Figure 32 - Sealing Between Appliance and Framing INSTALLATION Continued Figure 33 - Installing Optional Glass Door Spring Clip Insert Pin Into Spring Clip Insert Bottom Pivot Pin Into Pivot Plate and Swing Door Into Vertical Position Pivot Plate Slide Top Pin Into Door Track Screen Pocket INSTALLATION Combustion Air Kit Model AK4 (Optional) Appliance Enclosure Installing Optional Glass Door Accessory 108796-01E 16 Forr morre iinfforrmattiion,, viisiitt 5. Once the top and bottom pins are secured, unfold the door into the closed position. 6. Repeat the process for the opposite door assembly. 7. To adjust the doors, slide them partially open. Using a screwdriver, loosen the hold-down screws in the spring clip (see Figure 34) and pivot plate. 8. Close both doors until evenly joined at the middle and note the gap at the outer edges of the face. 9. Reopen one door at a time and retighten the upper and lower hold-down screws. 10. Repeat the process until both doors are evenly joined, spaced and working freely. CAUTION: The glass panels become very hot while the appliance is operating. Do not attempt to adjust or clean the glass doors until the appliance has fully cooled. The doors may be removed for replacement or cleaning as follows: 1. Partially open the door and press up on the upper spring clip with a screw driver until the outer top pivot pin is free of the clip. 2. Fully fold the frame assembly and slide the upper edge towards the center of the firebox opening until the guide pins are free of the frame rail (see Figure 35). CAUTION: Always operate the appliance with the doors either fully opened or fully closed. Operating the appliance with the doors partially open can result in improper venting of flue products. INSTALLATION Continued Figure 34 - Adjusting Glass Doors Spring Clip Hold-Down Screw Side Front Face Partially Opened Door Figure 35 - Removing Glass Doors Spring Clip Depress Spring Clip to Release Pivot Pin Remove Bottom Pin From Pivot Plate While Sliding Door Out of the Upper Track Pivot Plate Fold Bi-Fold Door After Releasing Spring Clip and Slide Door Out of Upper Track OPEN CLOSE VENT DAMPER MUST BE LOCKED IN THE FULL OPEN POSITION TO OPERATE THE APPLIANCE Figure 36 - Opening Vent Damper OPENING VENT DAMPER Vent damper must be locked in the full open position before operating the fireplace. If vent damper is not open, fireplace will not light. INSTALLATION Installing Optional Glass Door Accessory (Cont.) Opening Vent Damper OPERATING FIREPLACE For Your Safety Read Before Lighting Lighting Instructions To Turn off Gas to Appliance Optional Remote Operation 17 OPERATING FIREPLACE FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance is equipped with an ignition device which automatically lights the pilot. Do not try to light the pilot by hand. B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electric switch. • Do not use any phone in your building. • Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. C. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas c...
Ce manuel est également adapté pour les modèles :Autres accessoires pour la maison - M42E(B (3.11 mb)
Autres accessoires pour la maison - VM36E(B (3.11 mb)
Autres accessoires pour la maison - VM42E(B (3.11 mb)