Évaluations - , GPA:
(
)
)
Fabricant : Agri-Fab
Taille : 431.37 kb
Nom Fichier : 45-01001.pdf
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Facilité d'utilisation
45154 (9/92) RULES FOR SAFE OPERATION Preventing accidents is the responsibility of every equipment operator. The following general safety precautions must be fully understood and followed by every operator. 1. Do not at anytime carry passsengers in this cart. It is designed for carrying materials only and.not intended to carry passengers. 2. Do not tow this utility cart on a public thoroughfare at any time. The operator is risking injury from passing vehicles. Most local ordinances prohibit operating a cart and tractor such as this on a public thoroughfare. 3. When towing cart do not drive too close to a creek or ditch and be alert for holes and other hazards. The above could cause you to lot control of the cart and tractor. 4. Be careful on any grade (hill) and stay off of steep grades. 5. Maximum towing speed - 10 M. P. H. A LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS — ATTENTION. BECOME ALERT, YOUR SAFETY IS INVOLVED. Your utility cart carton and inner pack parts bag contain parts as shown in the figure below. The hardware package contains parts shown in figure 1 on page 3. Identify all parts and layout as shown in figure below and figure 1. CARTON CONTENTS LOOSE PARTS IN CARTON 1. Cart Body (2) 2. Tailgate 3. Front Panel 4. Draw Bar Tongue 5. Wheel Support 6. Wheels (2) 7. Axle 8. Tailgate Reinforcement Bracket 9. Latch Stand Bracket PARTS IN INNER PACK BAG 10. Tailgate Guides (2) 11. Corner Caps (2) 12. Hitch Bracket 13. Latch Lock 14. Latch Mount Bracket (2) 15. Hardware Package (not shown) CARTON CONTENTS 1 FIGURE 1 (FULL SIZE HARDWARE CHART) KEY QTY DESCRIPTION KEY QTY DESCRIPTION A 2 Cotter Pin 1/8” x 1-1/4” Long H 2 Hex Head Bolt 1/4-20 x 1-1/2” Long B 4 Washer 1.59 OD x .78 ID I 14 Slotted Truss Hd Bolt 5/16-18 x 3/4” C 34 Hex Head Bolt 1/4-20 x 1/2” Long Long D 37 Hex Lock Nut 1/4-20 Thread J 14 Lock Washer 5/16” E 2 Hex Nut 3/8-16 Thread K 14 Hex Nut 5/16-18 Thread F 2 Hex Head Bolt 3/8-16 x 1” Long L 1 Hex Head Bolt 1/4-20 x 3/4” Long G 2 Lock Washer 3/8” M 1 Extension Spring ASSEMBLY INSTRUCTIONS TOOLS REQUIRED FOR ASSEMBLY (1) Screwdriver (1) Pliers (2) 7/16" Open End or Box Wrenches (2) 1/2” Open End or Box Wrenches (2) 9/16” Open End or Box Wrenches 1. Remove the hardware pack and all loose parts from the carton. Be sure carton is empty before discarding. 2. Position cart body halves upright as shown in figure 2. FIGURE 2 1/4" x 1/2" BOLTS HEX LOCK NUT CENTER 3 3. Start 1/4" x 1/2" hex bolts and 1/4" hex lock nuts through flanges, only make finger tight until all six (6) bolts are in place. See figure 2. Tighten all six (6) bolts. 4. Position the wheel support in place on the bottom of cart. See figure 3. 5. Assemble wheel support to cart with eight 5/16" x 3/4" slotted head screws, 5/16" lock washers and 5/16" hex nuts. See figure 3. Heads of screws go to the inside of cart and should be tightened at this time. 6. Position the tailgate reinforcement bracket over end of cart. See figure 5. 7. Start 5/16" x 3/4" slotted screws through bottom of cart (heads of screws to the insic of cart) and reinforcement bracket. Secure finger tight with 5/16" hex nuts and 5/16" lock washers. See figure 4. 8. Position the tailgate guides so that the holes line up with reinforcement bracket and cart body. Refer to tailgate guide detail in figure 4. 9. Secure tailgate guides with six 1/4" x 1/2" hex bolts and 1/4" hex lock nuts. See figure 4. Tighten bolts assembled in steps 6, 7, and 8 at this time. Do not tighten others. FIGURE 4 10. Reverse the cart position and stand up on tailgate reinforcement bracket and proceed with assembly steps 11 through 18. See figure 5. FIGURE 3 FIGURE 5 11. Assemble front panel to open end of cart body, using 1/4” x 1/2” hex bolts and 1/4” hex lock nuts. Bolt heads to inside of cart. Leave out (2) bolts for latch stand bracket. See figure 6. 12. Assemble latch stand bracket using four 1/4” x 1/2” hex bolts and 1/4” hex lock nuts. See figure 7. 13. Assemble two front top corner caps and two bolts in top flanges through tailgate reinforcement bracket using 1/4” x 1/2” hex bolts and 1/4” hex lock nuts. See figure 8. Tighten all bolts. 14. Tighten all bolts assembled in steps 4 through 13, lower cart assembly to rest on top flanges, with axle support up. See figure 12 on page 6. 15. Assemble two latch mount brackets, latch lock and extension spring using one 1/4” x 3/4” hex bolt and 1/4” hex lock nut. See figure 9. Do not tighen 1/4" lock nut, latch lock must pivot freely. 5 16. Assemble latch lock subassembly to drawbar tongue using 1/4" x 1/2" long hex bolt and 1/4" hex lock nuts. See figure 10. 17. Assemble hitch bracket to drawbar tongue using 3/8" x 1" long hex bolts, 3/8" lock washers and 3/8" hex nuts. See figure 11. 3/8" x 1" FIGURE 11 18. Assemble axle and draw bar tongue to wheel support keeping open side of tongue facing up, make sure that latch lock snaps over latch ...