Évaluations - 2, GPA: 3 ( )

Fabricant : Axor Taille : 752.71 kb Nom Fichier : Langue d'enseignement:

©American Standard Inc. 2004 HOTLINE FOR HELP For toll-free information and answers to your questions, call: 1 (800) 442-1902 Weekdays 8:00 to 7:00 p.m. Eastern Time CANADA 1-800-387-0369 (TORONTO 1-905-306-1093) M968484 ROUGHING-IN DIMENSIONS TOOLS AND SUPPLIES REQUIRED 7271.301 7271.300 3° 3° [29mm] 1-1/8" [51mm] 2" [73mm] " DIA. [51mm] 2 [152mm] 6" [273mm] 10-3/4" [114mm] 4-1/2" [38mm] 1-1/2" 3/8" NPT FEMALE THREAD INLET 3/8" NPT FEMALE THREAD INLET [29mm] 1-1/8" [51mm] 2" [73mm] 2-7/8" " DIA. [51mm] 2 [137mm] 5-3/8" [114mm] 4-1/2" [279mm] 11" Adjustable Wrench Channel Locks Flat Blade Screwdriver Phillips Screwdriver Pipe Wrench Teflon Tape Plumbers' Putty or Caulking 1 2 3 4 FRONT-LOADED VALVE FOR ANGLED PANELS (AIR, GAS, VACUUM, WATER) FRONT-LOADED VALVE FOR STRAIGHT PANELS (AIR, GAS, VACUUM OR WATER) TYPICAL FUME HOOD FUME HOOD FITTINGS WALL MOUNTED REMOTE CONTROL OUTLET FITTING For installation of products refer to steps one to four. WALL MOUNTED REMOTE CONTROL OUTLET FITTING M968484 1 2 BODY SHOULDER WASHER HOLD DOWN NUT CARTRIDGE STEM HANDLE SCREW Important service note: The Faucet Panel mounted fume hood fitting has been designed such that future servicing of the fitting's cartridge can be done from the (user's) side of the fume hood. To do this, insure that the main supply valve to the fitting has been completely turned off and then purged by completely opening the fitting and releasing trapped material into the fume hood atmosphere. Then, support the entire fitting by holding the hold-down nut in place with a wrench, before loosening the cartridge's cap nut. This Panel mounted fume hood valve has been shipped as shown below to ease installation. It is designed to be installed in a 45° angled fume hood equipped with 1-1/2" (38.1mm) diameter mounting holes. Before proceeding with the installation, identify and familiarize yourself with all of the components. Important Note: The front load fume hood fittings described in these installation instructions are available in both right hand and left hand models. Right hand models are marked on both sides of the body with an "R" and left hand models are similar marked with an "L". Due to the use of these fittings in both right and left hand fume hoods, the bodies are marked on both sides with directional flow arrows. Regardless of the model used, the fittings are designed to be installed such that the inlet is on the bottom. 45° ANGLED FUME HOOD LOCK NUT FLANGE VALVE HOOD MOUNTING HOLE CROSS HANDLE CAP NUT PACKING NUT (7271.571 and 7271.521 ONLY) INSTALL FRONT-LOADED ANGLE CONTROL VALVE, 7271.021/521 (AIR, GAS, VACUUM, WATER) INSTALL FRONT-LOADED VALVE FOR STRAIGHT PANELS, 7271.071/571 (AIR, GAS, VACUUM, WATER) HANDLE SCREW NDEX BUTTON STEEL WASHER RUBBER WASHER BODY FIGURE 1 SHOULDER WASHER 1-1/2" (38.1mm) MOUNTING HOLE HOLD DOWN NUT Remove and flange from valve. Rubber seal washer, steel washer and lock nut valve Align the mounted are in line and the valve and valve body securely. With valve...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :