Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
THREADS 1-1/2 O.D. TAILPIECE 441mm (17-3/8) 70mm (2-3/4) 117mm (4-5/8) ROUGH FLOOR 102mm (4) 451mm (17-3/4) 24mm (15/16) 406mm (16) OPTIONAL TO FLOOR USUALLY BETWEEN 1651 & 1981mm (65 & 78) 711mm (28) C/L OF CURTAIN ROD USUALLY 1930mm(76) FROM FINISHED FLOOR C/L OF VALVES 102mm (4) 102mm (4) SPOUT- 1/2 N.P.T. FINISHED WALL SHOWER ARM- 1/2 N.P.T. 32mm(1-1/4) DIA. HOLE SEE NOTE 76mm (3) (2) 54mm(2-1/8) DIA. HOLES GENERAL SPECIFICATIONS FOR 2460/2461 WHIRLPOOL SAFE-T-HEATER REMOVABLE BLANK INSTALLED SIZE 60 x 32 x 17-3/4 In. (1524 x 813 x 451mm) WEIGHT 190 Lbs. (86 Kg.) WEIGHT w/WATER 607 Lbs. (273 Kg.) GAL. TO OVERFLOW 50 Gal. (190 L) WHIRLPOOL MIN. OPERATING VOL. 39 Gal. (148 L) BATHING WELL AT SUMP 41 x 20 In. (1041 x 508mm) BATHING WELL AT RIM 54 x 26 In. (1372 x 660mm) WATER DEPTH TO OVERFLOW 14 In. (356mm) FLOOR LOADING 46 Lbs./Sq.Ft. (220 Kgs./Sq.m) (PROJECTED AREA) PTS. 15.6 CUBE (FT3) 31.5 WHIRLPOOL ELECTRICAL SPECIFICATIONS SYSTEM I PUMP 1.6 HP, 9.7 AMPS,120V. SAFETY HEATER 12 AMPS, 120V. GENERAL INSTALLATION INFORMATION THANK YOU... for selecting an American Standard bath. Your new bath is shipped to you after careful inspection. The whirlpool version is completely assembled with pump, motor, and system piping. All you need to finish the installation are your selected fittings and electrical connections for a whirlpool. To insure maximum performance and pleasure from this product, please follow the instructions and cautions. List of Optional Components (not included): • Safe-T-Heater 9075.120* * see your American Standard Distributor List of Required Components (not included): • Drain 1583.470* • Bath Filler* * see your American Standard Distributor List of Required Tools and Supplies: Tools • Level • Tape Measure • Pipe Wrench • Slip Joint Pliers • Screw Driver • Standard Woodworking Tools • Personal Safety Equipment • Caulking Gun Supplies • Nails • Putty • Caulking (waterproof) • 1 x 3 or 2 x 4 Stringers • Drop Cloth • 15 amp GFCI Outlet • Cement, Plaster, Grout Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor immediately. After inspection and during installation, protect the bath from construction damage. After installation, and before enclosing with wallboard, tile, etc., water test the unit and check for leaks. Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump, motor, or piping system. Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and enclosing materials are provided by others. Check for availability of optional American Standard wall tiling bead (required for recess installations). Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth. WARNING! Do not lift whirlpool by the piping harness at any time. FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS. © American Standard Inc. 2003 791033-100 Rev. I All product names listed herein are trademarks of American Standard Inc. unless otherwise noted. FRAMING AND INSTALLATION BATH MAY ONLY BE INSTALLED ABOVE THE FLOOR LINE IN A RECESS TYPE INSTALLATION, AS SHOWN IN RECESS INSTALLATION DIAGRAM. LOCATE STUDS AS REQUIRED. INSURE ROUGH DIMENSIONS ARE PROPER, PLUMB AND SQUARE. FOR WHIRLPOOLS, PROVISION MUST BE MADE IN ALL INSTALLATIONS FOR AN ACCESS OPENING FOR SERVICING PUMP AND CONTROLS. THE FOLLOWING PROCEDURE MUST BE USED FOR ALL INSTALLATIONS: LEVELING SUPPORT STRINGER SHOULD BE AS INDICATED. THE BATH IS SUPPORTED FROM THE APRON AND THE REAR TILING FLANGE. NO SUPPORT UNDER THE SUMP IS NECESSARY. POSITION BATHTUB/WHIRLPOOL WITHIN THE RECESS, CHECK LEVEL, FRONT TO BACK, SIDE TO SIDE, AND SHIM AS NECESSARY. ALSO CHECK DRAIN CLEARANCE HOLE IN THE SUBFLOOR. TO SECURE THE TUB TO WOOD STUDS USE ROOFING NAILS IMMEDIATELY ABOVE THE FLANGE OF THE TUB. TO SECURE THE TUB TO STEEL STUDS USE DRYWALL SCREWS AND FLATWASHERS. CAUTION: TAKE EXTRA CARE WHEN DRIVING NAILS OR SCREWS TO AVOID D...
Ce manuel est également adapté pour les modèles :Autres accessoires pour la maison - 2461.XXXW Series (1023.05 kb)