Évaluations - 3, GPA: 4 ( )

Fabricant : American Standard Taille : 689.58 kb Nom Fichier : Langue d'enseignement:

... SPOUT RECESS Turn off hot and cold water supplies before beginning.CAUTION.. Assemble RUBBER WASHER (5) and BRASS WASHER (6) and LOCKNUT (7) onto SPOUT SHANK (4). Align SPOUT ASSEMBLY. From underside of ledge, tighten LOCKNUT (7) to secure SPOUT ASSEMBLY to mounting surface. SPOUT ASSEMBLY PREPARE TUBE AND TEE ASSEMBLY 2 3 1 1 2 1 3 5 6 Remove COUPLING NUT (1) and FERRULE (2) from each VALVE (3) and slide onto TUBING (4). 8" 2 7 4 MOUNTING SURFACE NOTE; Washer (5) may remain inside of Actuator Assembly. SPOUT ASSEMBLY MOUNTING SURFACE Install RING WASHER (1) into SPOUT (2) recess. Check that O-RING (3) on end of SPOUT SHANK (4) is in place. Insert SPOUT SHANK (4) into center hole on mounting surface. 4 Plumbers' Putty or CaulkingAdjustable Wrench 2.5mm Hex WrenchChannel Locks TOOLS REQUIRED REMOVE REPLACE Remove HANDLE (1) by removing INDEX BUTTON (2) and SET SCREW (3) with a 2.5mm hex wrench. Pull off HANDLE (1). Remove ACTUATOR ASSEMBLY (4). Remove WASHER (5). REMOVE HANDLE AND ACTUATOR ASSEMBLY 1 4 5 2 3 .. VALVE ASSEMBLY (1340.825; 1340.855; 1340.865) Install LOCKNUTS (1), METAL WASHERS (3) and RUBBER WASHERS (2) onto valve shanks. Push TUBING (14) ends into VALVE (4) side outlets. Insert VALVES (4) into mounting holes from underside of ledge. Press TEE (5) onto SPOUT SHANK (6) making certain that the O-RING (7) is properly seated on SHANK (6). Push COUPLING (8) into TEE (5) and attach to SPOUT SHANK (6) and tighten. 10 15 Thread of VALVE BODY (4) should extend at least 5/16 inch above MOUNTING SURFACE (11). If necessary, adjust LOCKNUT (1). Place RUBBER RING (10) into ESCUTCHEONS (9) and thread onto valves until snug against internal stop. MOUNTING Tighten LOCKNUT (1) to secure VALVE (4) position. SURFACE Slide FERRULE (12) and COUPLING NUT (13) to outlet of VALVE (4) and tighten COUPLING NUT (13) firmly. Place WASHER (16) on top of VALVE ASSEMBLY (4). Thread VALVE ACTUATORS (15) onto VALVES (4) and torque VALVE ACTUATOR 12-15 ft. lbs, (12-20Nm). Connect water supply to VALVES (4) with 1/2" IPS FLEXIBLE SUPPLIES or 3/8" O.D. BULL-NOSE RISERS. Use adjustable wrench to tighten connections. Do not over tighten. Be careful not to kink copper supply when bending. Use tubing cutter to cut to proper length. 5/16'' MIN. 9 2 4 10 11 13 MOUNTING SURFACE 1/2" IPS FLEXIBLE SUPPLIES or 3/8" O.D. BULL-NOSE RISERS 11 10 COLD 12 13 7 6 8 5 13 12 14 4 4 16 9 HOT 16 COUPLING NUT .. VALVE ASSEMBLY (1340.725) For Cold or Tempered Water Supply Valve assembly is same as two handle lavatory faucets. See above instructions for assembly, (1340.725 Single Valve Faucet) is for Cold or Tempered water only. 5/16'' MIN. 9 2 4 10 11 13 MOUNTING SURFACE 5 4 14 15 8 11MOUNTING SURFACE 10 COLD OR TEMPERED WATER 7 6 13 12 9 1/2" IPS FLEXIBLE SUPPLIES or 3/8" O.D. BULL-NOSE RISER COUPLING NUT 16 ... ....INSTALL HANDLES Remove INDEX BUTTON (1; 2) and loosen SET SCREW (3) with a 2.5mm hex wrench. Install HANDLES (4) onto VALVE STEM (5). Tighten SET SCREWS (3) with 2.5...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :