Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
Disregard the directions on the individual packages of OQUICK pHix It DOWNO and OQUICK pHix It UP.O However, the directions on the bottle of ONon-chlorine ShoxO and OBromine BaseO are correct. Always keep the chemicals away from children and pets. The first time you use the spa, you should test and treat the water. You must also treat the water each time you refill the spa. Once you have verified that the spa is functioning properly, and have allowed the water to circulate for a while, you should remove the spa cover and add 1/3 of the OBromine BaseO bottle, and 1/3 of the ONon-chlorine ShoxO bottle to the water in the spa. Allow the water to circulate for five minutes. You should now test the pH level of the water by using the included test strips. Refer to the test strip packaging for instructions on using the test strips. The pH reading should be between 7.2 and 7.8. If the level is too low, add half of one of the OQUICK pHix It UPO packets to the water. Let the water circulate through the spa for five minutes. Test the pH level again. Repeat until the pH level is correct. If the level is too high, add half of one of the OQUICK pHix It DOWNO packets to the water. Let the water circulate through the spa for five minutes. Test the pH level again. Repeat until the pH level is correct. See WATER CHEMISTRY on page 14 for information concerning proper water maintenance. STARTING THE HYDROTHERAPY SPA Once you have tested the GFCI, you should verify the water flow from the pumping unit. Set the air control on the console to the lowest setting (see USING THE CONSOLE on page 12). The pumping unit will heat the water as it pumps. Cover the hydrotherapy spa with the spa cover. The spa cover must be tight (see SECURING THE SPA COVER on page 11). The water will heat at about 1.8.F an hour with the cover on. If you are using the hydrotherapy spa indoors, and the room temperature is maintained at 70.F, it will take approximately 18 to 22 hours for the water to reach the set temperature. The temperature and water flow can be set or changed by the controls on the console (see USING THE CONSOLE on page 12). 10 Spa Shell Diagram Spa Shell Diagram A C B D SPA OPERATION Refer to the diagram above. The function of each component is explained below. The suction vents (A) located near the floor of the spa bring the water into the pump in order to operate the system. The suction covers should always be in place over the suction vents. Never operate the spa without the suction covers in place. The filter (B) can be removed for replacement and cleaning (see CHECKING AND CLEANING THE FILTER on page 13). The temperature probe (C) reads the current water temperature. Use of the console (D) is explained on page 12 of this manual. The hydrotherapy spa offers an automatic freeze protection. If the water temperature falls below 40uF, the pump will begin circulating the water to prevent the water from freezing. SECURING THE SPA COVER The spa cover can be secured by snapping the latches on the spa cover into the buckles on the side panels. The buckles can be locked by inserting the key and turning it clockwise a quarter turn. To unlock the buckles, insert the key and turn it counterclockwise a quarter turn. Latch Key Buckle Always keep the buckles locked when the spa is not in use. Keep the keys in a safe place, out of the reach of children. 11 12 Console Diagram USING THE CONSOLE Refer to the console diagram above. The function of each console control is explained below: Air Control: Determines the amount of air that is in the spa jet system during operation. If the control is turned to the left, the amount of air flowing through the jets will increase. If the control is turned to the right, the amount will decrease. On/Off Button: Turns the spa on and off. When you first press the on/off button, the spa jet unit will run at low speed, providing gentle hydrotherapy. Press the button again and the spa will run at high speed, providing more intense hydrotherapy. Press the button a third time, and the spa will shut off. The spa also features an automatic mode which heats and filters the water when the spa is left unattended. When the spa is first plugged in, or if the buttons on the console have not been used for longer than twenty minutes, the automatic mode will begin filtering or heating the water, as needed. Note: To keep the filter and heat cycles from running, the power cord must be unplugged. Thermostat: Controls the temperature of the water. The water heats at about 1.8.F an hour with the cover on. The thermostat can be set to heat the water from 70.F to 104.F. You should use a medical or other accurate thermometer to check the temperature of the water. Thermostat On/Off Button Air Control Maintenance The hydrotherapy spa is designed to provide you with years of enjoyment. Please follow the guidelines below to properly maintain your hydrotherapy spa. MAINTENANCE SCHEDULE DAILY . Check the water level and refill the spa to the level sh...
Ce manuel est également adapté pour les modèles :Autres accessoires pour la maison - Daybreak 408 WLHS43081 (652.85 kb)