Log:
Évaluations - 2, GPA: 4 ( )

Instructions Napoleon Fireplaces, Modèle GD82NT-PA

Fabricant : Napoleon Fireplaces
Taille : 4.81 mb
Nom Fichier : be94981e-acab-1554-01b8-58331d65a053.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


Pull the handles of the latches forward, then lift the hooks out from the slots in the door frame to release the top of the door. Next, pivot forward until the top edge of the door clears the front of the fi replace. Next gripping the sides of the door lift the door out from the retainer along the bottom of the door. LOG SHIPPING BRACKET Before installing the logs, you must fi rst remove the log shipping brackets. Lift up to remove. DOOR REMOVAL LOG SHIPPING BRACKET FINISHING FIGURE 37 FIGURE 38 Note: Due to the brittle material of the bricks, care must be taken not to bend or force them into place. Note: Refractory panels require a 24 hour curing period on a low fl ame. 1 2 3 HERRINGBONE PATTERN ILLUSTRATED 5. Rest the bottom edge of the rear panel on top of the rear portion of the air defl ector at the back of the fi rebox and push into place. The rear panel is held in place when both side panels are in position. 6. Install the left brick panel using the same method described in step 4. 7. Replace the burner, air defl ector, logs and glass door. FIGURE 43 DECORATIVE BRICK PANEL INSTALLATION Decorative panels may discolor after time. 1. Carefully remove the glass door and all logs. (Refer to the “FINISHING” section) 2. Remove the two screws holding the front portion of the rear air defl ector. Remove the pilot shield by removing the two screws as illustrated. (Fig. 40) 3. Remove the 3 screws holding the burner down and carefully remove the burner. (Fig. 41) 4. Install the right brick panel by sliding the bottom edge of the panel down the right fi rebox side then pivot the top edge of the panel into place against the fi rebox wall. Hold in place with the brick retainers. (Fig. 41) STEP #2 PILOT SHIELD FIGURE 40 STEP #3 FIGURE 41 FIGURE 42 20 W415-0665 / B / 02.11.08 1. Attach screw and spacer as illustrated in (Fig. 44) to the bottom of both sides of the front housing. 2. Attach the face plate bracket provided to the top edge of the front housing using 2 #8 - 1/2” truss head screws as illustrated in (Fig. 45). 3. Lift and hook the faceplate over the spacers, and push the top of the faceplate back until it comes in contact with the base of the turn button. To secure the faceplate simply turn the head of the turn button to the horizontal position. (Fig. 47). SCREW & SPACER NOTE: A 1/4” gap must be maintained between the front and all fi nishing material due to regular removal. AFK / WI FACE KIT INSTALLATION FIGURE 45 FIGURE 44 FIGURE 46 FIGURE 47 5. Place log #5 so the locating hole on the bottom of the log sits on the screw and spacer. 6. Finally, align the rectangular peg on log #6 with the notch on the front right portion of the burner. NOTE: Decorative brick panels must be installed before the logs. See installation instructions supplied with the panel kit. LOG PLACEMENT PHAZERTM logs, exclusive to Napoleon® Fireplaces, provide a unique and realistic glowing effect that is different in every installation. 1. Place the rear log #1 onto the locating studs along the back edge of the PHAZERAMIC ™ burner. 2. Position log #2 in the 2 locating holes behind the andirons. 3. Place log #3, with the charred branch facing inward. Position the pin in log #3 into the hole on the left of the log #2. GLOWING EMBERS 2 3 4 1 FIGURE 39 a-f Glowing embers are NOT recommended. The burner has been designed to achieve maximum glow without embers. 5 6 4. Place log #4 with the charred branch facing inward. Position the pin in log #4 into the hole on the right of log #2. 21 W415-0665 / B / 02.11.08 SERVICING / REPLACEMENTS 1a. Rectangular Front Removal Pull on the top of the optional front away from the fi replace until the male portion of the latch disengages. Tilt forward slightly and lift from the 2 shoulder screws near the bottom. 1b. Heritage and Wrought Iron Front Removal Turn the head of each turn button from a horizontal position to vertical. Allow the front to tilt forward slightly and lift from the 2 shoulder screws near the bottom front. Note: Fronts are heavy so when the second turn button is turned the front will want to fall forward. See Figure 51. 2. Control Panel Removal Tilt control panel away from the door and lift from slots. See Figure 53. 3. Turn Power and Gas off to the unit. 4. Door Removal. See door removal section. 5. Burner Removal Start by removing the logs being careful since the logs may still be warm. Remove the 2 screws holding the air defl ector (Figure 52a) then remove the 3 screw holding the burner (Figure 52b). Lift burner from fi rebox. 6. Remove the 5 screws securing the burner base. Once the gas has been disconnected, the valve train assembly will lift out. Service components as required. BURNER AND VALVE REPLACEMENT FIGURE 51 REMOVE 4 SCREWS BLOWER MOUNTING PLATE BLOWER REPLACEMENT Your comes equipped with a heat circulating blower. The blower is pre-wired and is controlled by the remote control supplied with the unit. Drywall dust will penetrate into the blower bearings, causing irreparable ...

Ce manuel est également adapté pour les modèles :
Autres accessoires pour la maison - GD82PT-PA (4.81 mb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories