Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
If a power-up occurs, system returns to default setting (.F). Turning the light on: Press Light to turn light on. Pressing a second time turns light off. A built-in timer automatically turns light off after 2 hours, unless manually deactivated first. The "Light" indicator is displayed when light is on. Fiber Box Option: If spa has an optional fiber box, press Light key to turn fiber box (motor and light) on. Pressing a second time turns fiber box off but leaves light on. A third time turns both motor and light off. A built-in timer turns fiber box off after 2 hours, unless it has been manually deactivated. The "Light" indicator is displayed when fiber box light is on. It flashes when fiber box motor and light are on at the same time. LED Light Option: If spa has an optional LED light, Press Light key to turn LED lights on. To advance to the next color/display setting, press Light key twice. The LEDs will go off with the first press, then back on in the next setting with the second press. If the LEDs remain off for more than 5 sec., the color/ display sequence will reset and start back at the beginning the next time the Light key is pressed. Color/ display sequences are: 1• LEDs light up and slowly cycle through all six colors. The slow cycle restarts at the beginning and repeats. 2• LEDs light up and remain on in Aqua. 3• LEDs light up and remain on in Purple. 4• LEDs light up and remain on in Blue. 5• LEDs light up and remain on in Gold. 6• LEDs light up and remain on in Green. 7• LEDs light up and remain on in Red. 8• LEDs light up for 2 sec., flash off, then flash on in the next color until all six colors have been displayed. The flashing cycle then repeats itself. 9• LEDs flash on/off quickly for a strobe light effect. A built-in timer turns lights off after 2 hours unless manually deactivated first. The "Light" icon is displayed when LED light is on. QuickReferenceCard Automaticwaterheaterstart: Economymode: When water temperature is 1.F (0.5.C) lower than Press Econo key to switch from Normal mode the Set Point, the heater will automatically turn on until to Economy mode. In Economy mode, system water temperature reaches Set Point plus 1.F (0.5.C). maintains temperature at the desired Set Point during filter cycles only. Set Point is 20.F (11.C) The "Heater" indicator lights up when the heater is below the Normal mode Set Point for the rest on. It flashes when there is a request for more of the time. In Economy mode, the display will heat but the heater has not yet started. toggle between the current water temperature and the "Econ" message. N.B.: If your system is configured in Low Current Mode, the heater will not start if a pump is on at high speed. PROGRAMMINGFILTERCYCLEDURATION The system automatically performs two filter cycles per day, at 12-hour intervals. During a filter cycle: Pump 2 runs for one minute, then Pump 1 runs at low speed for the programmed number of hours The "Filter Cycle" indicator lights up when the filter cycle is on. To set filter cycle duration: Press and hold Filter key Use Up or Down arrow keys When the desired setting is dis- until the display shows "xx", to change setting. played, press Filter key to confirm. representing the currently 0 = no filtration A filter cycle starts immediately. set filter cycle duration in 12 = continuous filtration hours. The filter cycle is suspended if the water temperature raises more than 2.F (1.C) above Set Point or if spa is in use (pumps started manually). The "Filter" icon will flash (on 0.5 second, off 0.5 second, on 0.5 second, off 1.5 second). TROUBLESHOOTING 3 flashing dots are displayed. Water temperature is flashing. The display is flashing. Pumps have started up for one minute on several occasions and "Filter Cycle" indicator is flashing. Note: Light needs to be turned off before the filter cycle can be programmed. N.B.: After a power failure, the filter cycle duration will return to its default value (2 hours). In this case, the first filter cycle will start one minute after power has been restored. Not a bug but a feature! Our Smart Winter Mode protects your spa from the cold by automatically turning pumps on for one minute several times a day to prevent water from freezing in pipes. A problem has been detected. Do not enter the water! Check and open water valves. Clean filter if necessary. Check water level. Add water if needed. Shut power off and power your spa up again to reset the system. Call your dealer or service supplier if problem persists. Water temperature in the spa has reached 112.F (44.C). Do not enter the water! Allow water to cool down. The system will reset automatically when water temperature reaches 109.F (43.C). Call your dealer or service supplier if problem persists. A power failure has occurred. Press any key to reset the system, then reprogram all desired parameters. Smart Winter ModeTM 9919-100578-B ...